Viewing all customer Discussions for:

26-120 LH Top Tilt Latch, 2-1/8"

Our client is looking for the tilt latches for the vinyl single hung window. They told us that it was Milgard window's single hung windows. We showed all the photos and information to Milgard window's service department, but they are sure that their single hung window had never had the tilt latches ... (cont.)

Buying a home that has Daco on the the window locks. The latches are on both sides of the window that allows you open same.

I am looking for replacement tilt window latches for Castle double hung vinyl windows. Visually and dimensionally, they most resemble your 26-228/229 parts. However, mine are 1-11/32" wide, 2-3/32" hole center, and have a 3/16" diameter boss that sticks out the bottom about .100. Hole diameter is 3/ ... (cont.)

Hi, I had purchased these latches from your shop several years back and now need more. Numbers on the back: 11147 L 3 PAT,#4,901475 I would need 15 of each right- and left-handed latches (a total of 15 pairs; 30 count total). It looks very much like part number: 26-228 (R-handed tilt latch ... (cont.)

No numbers or markings on existing latch

There are no markings I can find on the windows. even looked on the spacer. Know the corners are NOT welded. :( Any information about the windows and parts that are available will be appreciated. Thanks in advance.

The first picture is a tilt latch 3" long. Everything I saw on your web site is less than 3". Second picture is a nylon insert that the screw holding the top of the spiral balance goes into. Can't find it anywhere.

I don't have a name or anything I am looking for 7 of these for each direction. Any thoughts that you can identify these? Jesse

Hi The moving piece inside is broken, I should buy both right and left. There are no markings on the window or on the latch 3 1/8" x 1 3/8 " 1/4" thick 2 1/8" between holes while plastic it is screwed on top of the frame, it is not recessed into the frame (I would like the same bec ... (cont.)

Hi! I have to replace several sets of these in my home before i can sell it. The windows were installed in 1999, before we purchased the home. The company which installed the windows seems to have gone out of business, and no one local has any latches that will fit. The dimensions of the piece pi ... (cont.)

I bought some replacement latches but the part that retracts is too short to extend into the frame. The old latch shown on the left is 3 1/8 x 1 3/8. Please give me the dimensions of the length of the part that retracts so I can be sure it will work. The section that extends is 1/2" The existin ... (cont.)

Need help replacing my latches in my home. I hope the pic helps. Some of your products look close but I cant find an exact match. Any help would be great. Thanks Lance

white vinyl 3 1/4" lenght 1 1/4" width 1/2" lock 1 1/4 between screw holes number on latch 11148 Thank you

I see that on item 26-120 that the holes are 2 1/8" apart. What are the other demensions? Thanks, Dennis

Hi, I need to replace a few window latches that have broken. The dimensions are as follows: 2-1/8 inch attachment screw holes 3/4 inch from screw hole to end of casting (not including sliding latch) width is 1-3/8 inch thickness is 5/16 inch Based on your site, I see either the 26-120/12 ... (cont.)

Hi guys, I need surface release replacement mounts for Traco double hung windows series TR 4300; I took a picture of label,can mail it if needed but,rest of it goes as follows; 851771 062503 202-008 I appreciate your help and would like to order parts if you have them ASAP

I needed to replace a few broken latches on windows I had installed 17 years ago. The SWISCO website was very helpful in matching the parts needed. The cost and shipping was very reasonable. This was a very small purchase but on another company's website, the cost would have been three times as mu ... (cont.)

Need at least 3 pr. of window latches. Not the locks but the plastic latches that snap into the jamb. I was told i need 26-121 R and 26-120 L Can you help me out? Thanks! Steve

Would like to see if this hardware is still available. If so would you contact. Would need a quote for the following: 108qty of 21" prod code S600-21 50 qty of the tilt latches "see picture" I couldn't find this on your website but the deminsions are 2 1/8 on center screw holes/ 54 qty o ... (cont.)

The one that I need is very close dimensionally to your # 26-120. My dimensions are 3 3/16"long, 2 1/16"centers of holes, 5/32"thickness of latch, 5/16"thickness of body, 1 11/32"wide, 3/4"center of hole to latch end of body. The disparity with the centers of holes dimension concerns me the most ... (cont.)