Viewing all customer Discussions for:

81-269 Lupton Roller Assembly, 1-1/4" Steel BB

Can these be overnighted ASAP

Hi there, I'm trying to find a replacement my sliding door roller assembly. (Or just the wheel, if that's better.) It has a metal wheel, and it seems to be 1-1/8" diameter, at the *widest* part. It looks very similar to this one: https://www.swisco.com/Lupton-Roller/pd/Patio-Glass-Door-Single-Whee ... (cont.)

All the dimensions match part no. 81-269 except the metal roller is 1-1/8" dia. Can this be replaced with a nylon roller or a 1-1/4" roller? This sliding glass door is in a beach house. Please advise. Thank you

Have a metal sliding door, says "International" on the handle. No other markings. I need to replace the rollers, picture of one attached.

Hello, This appears to be one of two rollers for my sliding glass door: I have no idea what brand it is, there are no embossed brand names, nor are there any stickers. The bearings on these are completely shot. the box is about 3/4" thick, by 1 3/16" high. the roller is steel, and the outer diam ... (cont.)

Can you help he determine the correct rollers for my siding glass door? I don't have the night or the wheel size, the the length is 2 1/2" and the with is 3/4".

I have an old Likit sliding glass door needing new rollers and track cap. See my pictures which look like your PN 81-269. Is this the right PN? Does this roller work with the small track cap PN 80-102? Or can you suggest another roller that would fit in my door and work with the track cap? Thanks ... (cont.)

Roller wheel is metal and seems 1 1/8 inch diameter. Length of housing is 2 1/4 inch. Height is 1 1/4 inch. We need two of these. One for each end of the door. Door seems to be original to the house which was built in 1981. Not sure what other information you need.

Greetings, Can you suggest a replacement part for the roller assembly on our old closet doors? Housing 5/8 inch Housing height 1 1/4 inches Wheel diameter 1 1/4 inches Wheel width 5/16 inches (.8cm) Main body length (top) 2 inches Main body length (bottom) 2 3/16 inches Body length with bent piec ... (cont.)

My name is Ray. This is a old 1978 Likit sliding glass door 8 foot. Wheel supports are broken. do have a good replacement part roller assemblely.

Good morning, I'm searching for Sliding Patio Door Rollers. I believe it's a Milgard Sliding Patio Door base on the window sticker "MFGR CODE MG-4". I'm sending a photo. Hopefully you will be able to supply me with a pair. Thank-you Larry

I bought several 81-269 single wheel roller assemblies based on matching appearance and measurements to my existing rollers (multiple doors). What I didn't account for is that on my existing rollers, the wheel drops about 3/16 inch further down below the steel housing than the 81-269 replacements t ... (cont.)

1 1/18 inch metal wheel diameter 11/16 width

I need to find this part

See above trying to find correct roller for two sliding patio doors. Attached are photos of rollers. It looks like your part number 81-243 is similar and believe roller is 1 1/4 inches in diameter. Found one at Home Depot but body of roller was just a bit too wide and grove on side of body was too n ... (cont.)

The only branding I could find was on the outside handle. International is the brand and/or model.

Sorry - I did not take installed pictures

scrolled through your sliding screen door wheel selection and didn't see this on. did not see any identifying info on them or the screen door itself. actually a decent sliding door if it would just roll properly. please advise. Thanks, ken

I need to replace this roller I need 4pcs. Thank you in advance!

Looking for a replacement for Arcadia installed 1964