Viewing all customer Discussions for:

79-029 Weatherstripped Faceplate, Short Throw

Hi, I am looking for the face plate in my photo in white, it measures 6-7/8 in long x 1-1/8 in Wide The two bottom holes are 2 inch center to Center Throwplate opening is 2.3 inch The Top single Screw Hole is .5 inch from the edge between the top and the throw plate opening Do you have this it ... (cont.)

Looking for the correct part to fill this gap that is in the lock area

Looking to replace this Faceplate which has weatherstripping please

Looking for an astragal weatherstripping similar to 58-085 but with a pile projection of 1/2"

Didn't find any numbers or markings on the weatherstripping or the door

need to order 1 1/8 " wide. (Aluminum; Face Plate w/ weatherstripping) need quote with ETA and total cost

Bobby

Hello I need weatherstripping for this commercial door including the piece around the latch. Is this something you can help me with? Top piece is 31 1/4" and bottom is 45" plus the assembly around the latch. Thanks!

The entrance door weatherstripping is need of replacement. 8' long 1/2"x7/16 and mortise lock double mohair.

I purchased the weather strips for our two entry doors from you and now I need the weather stops for around the two locks. Can you point me to the correct part number?ThanksJoe

We have a Kawneer door that I thought part 79-030 would fit, but it does not quite. 1.Your part is 1" wide, the Kawneer is 1 1/8". Your part would leave a slight gap on one side, allowing rain to enter the door unless sealed somehow. 2.Your part is 1/16" longer (it could be filed down, if that was ... (cont.)

Could you please give me some advice. I just bought an old building that's been neglected. 3 doors. all metal standard size. all exterior doors. The front doors has the only professional insulation on one side. Took a sample (like you side in the video) 1/2" wide, 1/2" thick pile. Lots missing. Can ... (cont.)

Need help with the kind of sticker plate s that I have pictures for

I have to replace the door weatherstripping ( 58-085) but we recently had push bars installed on the church front doors and they replaced the existing deadbolt and now we have this blank faceplate. the faceplate measures 6 3/4" tall by 1 1/8" wide . do you carry anything that would weatherstrip this ... (cont.)

We don't have the manufacturer.There is a small piece missing. It probably just slid out of the slot since there is a 2 inch gap where the door lock is and it might have slid out there.It looks like a total of 1.5 inches wide with the aluminum holder and 3/4" for the bristle part. ... (cont.)

which ones will work? How do I know if it's short or long faceplate? Which doorsteps will work?

I see on the latch cover Adams Rite. Cover has a pile on outside. It's in one of the pictures. Door weatherstripping runs inside aluminum Chanel, which held on the door by screws, with same screws hight can be adjusted. V. Metrikis.

Hello, I've attached some pictures of the door and my business shop. Per the health department, I need to get the door gap closed and have enclosed some pictures. Could you please advise as to what may be the best to get he gap closed? We also need to replace the sweep on the bottom. Thank you! Laur ... (cont.)

How long is the pile on the weatherstripping on this face plate? It doesn't say in the product description. We will likely need somewhere around 3/8 and just want to know if we need to order some other pile in order to replace the one that comes with the face plate. Thanks!

I have an aluminum frame door that is missing the pile weather stripping. It looks to me that I can slide a new strip in the channel. It is a 1/4 wide but the inside is maybe an 1/8 bigger on either side. It probably needs to be 1/8 tall