Viewing all customer Discussions for:

10-325 30" Shower Sweep With Drip Rail

Hi, I have attached two photos of my door sweep. It would be great if you can recommend a replacement part. Thanks!

The sweep is about 22 inches wide. It appears to be a makeshift deal.. My question is : will your 10-325 work for this situation

My contractor threw away the fasteners. Do you sell new fasteners? If so,which ones are they and how much? And what do I need to drill holes? Also, do I need to put a drop of silicone on the end to keep the water from rolling out? My old one had that. Thanks?

The clear rubber material is about an 1" on the longest side. I hope this looks familiar in some way. I can't find a similar cross section part. I can't find the door mfg either. Thank you. Dale

does this come with the rubber sweep and if so what is the deminsion from bottom to top?

Any idea how to remove this old drip rail so that I can install your 10-325. The old one lets water leak out onto the floor.

Current sealing is not working well. Water is leaking past the seal and I assume this needs to be replaced. I am looking for a high quality replacement. Additionally current configuration has large gaps at either ends. Is there a better option to replace the hardware at the bottom to ensure end to e ... (cont.)

I have a pivot shower door, probably Aluminum, for which I am needing the bottom sweep. I have attached some pictures as a reference. Please advise if you have this door and how much does it cost to ship me and how long does it take to reach me. I am in Dallas Tx. I would appreciate your response. ... (cont.)

I would like to know if your 30 inch drip kit will fit as my replacement shower. It is 30 inches but the screw holes are placed sporadically. First hike is 3.5 inches from end then next hole 9 inches from that hole then next hole is 15.5 inches away from 2nd hole.

Need shower seal replacement?

How far apart are the screw holes in the 30 inch shower sweep?

My shower door sealer mounts to a rail, from the side. Do you have this?

This is a 29" swinging glass door. Any clue on what I need to replace this strip with? Do I need to replace the whole bottom part after removing two screws?

Looks to be longer than 1inch to stop water from coming out. Please advise! Thank you for your expertise! LJ

Hi could u help me find the correct shower door sweep When I went to clean it I pulled the plastic part out and it just kinda fell apart Went to Lowes they said I should buy new door My husband isn't very handy...but I still love him So I usually end up doing these things Any help would be gre ... (cont.)

I need to replace a black rubber sweep on a shower door. I do not know the door manufacturer. The sweep is about 3/4 of an inch wide and has a semi round about 1/8 in top. See photos. Where can I get the rubber sweep or do I need to replace the sweep holder also? Thanks! For your assistance. Don ... (cont.)

The photos are showing 2 sections of inner shower door one with seal in place and the other with seal missing from extrusion. The last picture is just of sliver of the piece that fits in door. I purchased a piece 10-319 but it isn't even close to correct piece flap is too small. Hope this helps. Tha ... (cont.)

Hi. Water escapes my shower, and I was told I am missing the door sweep. The ones on your site seem to have the screw holes in different places than mine. This shower door is 27" wide. It seems I would need a 25" or 26" door sweep. There is 21 1/2" between the screw holes. Do you sell anyt ... (cont.)

Here are 3 images and a sketch of the gray vinyl sweep I am trying to replace. Kindly let me know if you might have it. Thanks

Hopefully, these photos will be of assistance in coming up with a solution. The original rubber (vinyl) strip on the shower door rail is kaput. Home Depot was of no help. They had me buy a shower door bottom seal that was very flexible and did not work. I measured the rail and rubber portion and the ... (cont.)