Viewing all customer Discussions for:

81-166S Dual Roller Assembly, 1-1/4"

I have an 8 foot slider that needs new rollers. Do I need both top and bottom rollers? What size in inches - 1 1/4, 1 1/2? Thanks for any hel you can offer!

I have a 60" sliding patio door , vinyl, and need some rollers and will probably like to replace the track [ door put in when the house was built in 1999. The track just snaps in . Wheels are 1.25 in. diameter , body of the housing is 3 1/8 inch wide thank you!

There is no info or part numbers on this assembly. There are two assemblies in my door. The frame of the assembly is 3 1/8 inches long and 1 1/4 inches tall. The wheels are steel and are 1 1/4 inches in diameter. The width of the front of the assembly is about 11/16 wide. Can you please ID a part nu ... (cont.)

Hello, I have a white vinyl sliding patio in need of roller assembly replacement. It's a Hayfield 3100 Series. Can you please provide information on the assembly? I will need two. Thank you, Steve

Hello, I looking for replacement rollers per picture. Wheel diameter: 1 1/4" Housing width: 11/16 Housing length: 3 1/8" Housing height: 1 1/4" Metal rollers

I could not find any branding or identifying numbers or marks on any of the hardware pieces or on the door. The window did have the name Guardian etched into it with other information that appeared to pertain to the glass itself, I did include a picture of it. Thanks for any help you can provide. ... (cont.)

This is the rollers in my Pella sliding glass door no numbers on it can you tell me the replacement parts I need please.

Series 870 a Philips product looking for the rollers my door has tandem rollers on each roller and there are two rollers on the door l would like to know how much if you have them? Send picture so l can check message's l have not look at rollers that good Thank u for your time my dather Taryn sent ... (cont.)

These are 22 years old, from when the house was built in 1999. Wheels are 1.25" in diameter. Housing is 1.25" tall, 5/8" wide and 3 1/8" long (hopefully we measured correctly!)

No identifying info. Measurements: .67 inch wide, 3.11 inch long, 1.29 inch high. Rollers are 1.25 inch.

3 inchby 1 1/4 square box 2 2/8 by 1 1/4 wheels

Hi, I am looking for replacement parts for my exterior sliding glass door. The sliding door is vinyl and is 93 1/8" high, 36 3/4" wide. I need a set of rollers for the bottom left and right sides of the door as seen in the attached 3 photos. I also need a new door handle inside, outside, and the loc ... (cont.)

Looking for replacements and it looks to me like your 81-166S might be right? I believe the body is 3 1/8" long by maybe 1 1/4" high and 11/16" wide.

Just need rollers for an 8 ft slider

Need new pair of rollers for my sliding glass door. See attached photo for part. Thanks

We need two replacement roller mechanisms for our Guardian skidding glass door.

No numbers on hardware but the door glass has the name Guardian on it. My measurements are 5/8 wide X 3 1/8 Long X 1 1/4 height.

Hello, one of my rollers is completely shot and makes it a constant trouble to close and open the door. Yes the track is separating but the main metal track cover looks fine. I figure just replace both rollers but want to make sure your rollers or the correct part. Can you please advise what you hav ... (cont.)

Hi. There are no markings on the door other than the sticker in the picture. The door is very heavy and has two tandem rollers at the bottom (pictured). I found a couple in your list that appear to be the same but I am not sure which one is the correct one. Thank you. Barry

Wheels probably 1.5". Bad picture, wasn't centered over wheel. After lubricating rollers, placed back on slider. Wheels wouldn't rise enough off bottom guide. Not sure if rollers are damaged/out of round or if housing in vinyl slider is damaged, allowing the assembly to retreat into housing in v ... (cont.)