Viewing all customer Discussions for:

32-012 Rear Drawer Track Socket Pair

I need to find a replacement for this back mount to my sliding drawer. Could you advise if you have a replacement for this.

I unfortunately do not have any names, numbers or markings. It is from a kitchen cabinet drawer likely installed in 2006. Thank you for any information you can provide on any replacement part that might work. The inner part of the backplate where the drawer rail would fit measures 1 1/8 " by 1 7 ... (cont.)

Need slide sockets for bathroom & kitchen drawers. I've visited several stores & did not/could not find these particular slide sockets. Please Help.....Thanks

merlillat 1991 vintage drawer slides rear mounting bracket, can you replace these?

This part is close to your 32-119 but I would prefer the snap-in rear mount. I've tried the screw mounted rear brackets, but they didn't work for my cabinets. Thank you for your help!Marty

The right side of our slider drawer broke. I took a picture of the left side so you could see the part and the broken piece. Can you tell me what to order?

Kitchen drawer

Good day. Please help me find a replacement part that will not require me to drill! Thanks so much.

I need the plactic piece u see in photos that the runner fits into. This is on a merrillat kitchen cabinet drawers. It has side mount runner that fits into plastic piece on back of cabinet. The drawer then fits into the cabinet side rail. Notice how the rails are angled down at end as it goes in pla ... (cont.)

The cabinets were installed in 1992 by the previous owner so I do not know the manufacture. The inside dimensions of the socket are 3/8 by 15/16 and 1 1/4 deep. The exact replacement would of course be best, but if there is one that requires screw mounting with everything else correct then that wo ... (cont.)

Hello, I am trying to find larger Drawer Track Back Plates. Mine are close to 30 years old. Your 32-089 looks close, but the 3/8" opening should be 7/16". I will attempt to send a picture. My broken one is on the left. The one on the right is a Liberty brand from Home Depot and it is too small. Can ... (cont.)

This piece broke today. Need a replacement. The area to insert the railing is 1.5 inches tall by 1/2 inches wide. It slides to adjust. It is attached to the mount, which is 2 inches wide and 2 1/4 inches wide.

Hi, I was looking on your site to see if you have any replacement parts for a 1990 Merlilat kitchen drawer. I have uploaded few pictures one is the sticker another is a functioning part and the other shows the broken one. if you could tell me which part I would need, I would like to purchase a cou ... (cont.)

track back plate has broken so there is no suport for the side rail. I think maybe I need 32-089? My side rail is 1" wide. The back plate is broken in a couple of drawers--1 is a kitchen utensil drawer that is about 22" deep and other is a desk drawer that is about 16" deep but except for the len ... (cont.)

I need to replace broken bracket. Need item number.

The rear tracker has a plastic tab/button that snaps into the back of the cabinet, no screws.

I had a pull out drawer socket break, this was at the rear of the cabinet. It's a plug type and not screwed into the cabinet so there are two big holes there now. The cabinets are Merillat and I know they don't have these anymore, and was hoping you had a replacement part that would cover the exist ... (cont.)

I need the right side bracket and hope the photo is good enough for you to decide what I need. Please let me know if you can help me. Other then the shape of the back the measurements you have on your diagram from what I can tell are the same as 32-146. I was thinking 32-012 looked like a clo ... (cont.)

The picture second to the right shows the intact side, the left. The right side cracked. The piece is actually two plastic pieces, one that slides into the other and locks in. The picture on the most right (or second row) shows the inside of smaller piece while it is slid in, though the lower par ... (cont.)

Left side of bracket that holds track for kitchen cabinet draw it broke now I am trying to replace it