Viewing all customer Discussions for:

32-061 21-5/8" Self-Closing Drawer Slide Pair

Need new side rails and the tracks for kitchen cabinet drawer.

I was recently given a dresser "Impressions By Thomasville" the draws are a death trap. I'm thinking i need the hardware that connect the drawers and dresser and allow them to slide. Would rather have someone come and do that for me, but i doubt its an option. Drawers dont slide out they fall out ... (cont.)

I'm looking for the mirror image match for this roller. This is from the right rear of the drawer as seen from the back. I need its mate, to go on the other corner, so the roller projects to the left side of the drawer (as seen from the back). All it says on the bracket is "GRANT DR." I've been to ... (cont.)

The back mounting bracket broke. Cant find.

I need to replace the small brown plastic bracket in our kitchen lower cabinet. The cabinets are no longer being made and Home Depot and Ace Hardware did not have anything similar that would allow us to use the sliding drawer/shelf. Please let us know if you have a mechanism that is similar. Or perh ... (cont.)

Hi Cabinets were installed in 1995. Haas Cabinets. As you can see from the picture, there is a round insert that fits in a metal connector which is riveted to the back of the cabinet wall. Do you have this part and or a recommendation for a replacement. Regards Brian

I'm looking for a drawer socket to accommodate the narrow flange that reaches down from the bottom of our track. We have several drawers that are failing.

I'm looking for an under mount drawer guide that will replace a Mepla 2035/572. Do you have anything like that? The measurement from the back of the drawer front to the back of the drawer box is 20.75". The measurement from the front of the cabinet face to the back wall of the cabinet is 23.5". This ... (cont.)

Need this part

Bottom slide that is attached to the drawer

we ordered the part that was recommended to replace the mepla part that was installed on our cabintets Mepla543.000. roll/x 20357572 but seems that the lip of the rail of the new part is too wide to fit into the drawer. we are at our wits end. please help.

Need replacement sockets for 25+ yr old hardware that has 1 1/4" tall drawer tracks. Do you have sockets that accept these older (and larger) tracks? Seems that current standard is just 1" tall.

I just bought some unigrasso 6600 drawer slides. They worked . Now I need the same type of glide or slide for 3 other drawers. See the pictures. Please recommend the proper hardware needed.

The rear brackets for our pots and pans drawer are broken. See attached photos. Note that these brackets have a stub which fits inside the rail. The inside dimension that the stub will have to fit into is 13/16".If there is no replacement part available, can you recommend full rail and bracket syste ... (cont.)

Looking for unigrass draw slides. 21-5/8". Need drawer and wall attachment slides. Imprint on slide " Unigrass 6600".

Replacing a Unigrass 6600Hi Swisco,Spoke to Tim a few weeks back and he suggested that I send photos. Attached you will find photos of the railing on the inside of the top dresser drawer and then the photo of the railing on the drawer side. I took a shot of the far back of the drawer just in case yo ... (cont.)

KV 1284-3

Hi my name is Shannon. I purchased used kitchen cabinets with drawers for my craft room and was unaware that half of the drawer slide hardware was missing for 3 of the drawers. I have the tracks that mount to the bottom side of the drawer but I need the tracks and the other 2 pieces of hardware tha ... (cont.)

I have two different drawers. One is 22" and the other is 21 3/4" deep. The cabinet is 22 5/8" deep inside. I need replacement parts for two drawers of each depth.

The part that goes on the drawer is 22". The piece that connects to the cabinet is 24", but 1" is bent at a 90" angle so that it can attach at the back of the cabinet.