Viewing all customer Discussions for:

39-026 Awning Window Crank Operator

Guessing circa late 60s, need 5 operators and other parts.

Inside of handle says -11500-11 patent pending Bottom of mount has the letter K Arm says 78 Middle joint of arm says 91 (underlined to show it's 91 and not 16) Arm needs to have the nub (thread bushing??) so it can attach to the outside arm Photo with drawing of measurements attached. 5 1/4 betwe ... (cont.)

I have a couple that are broken and need to be replaced.

I have old casement windows and I am having trouble finding a replacement crank that fits the window. Do you have cranks that might fit I will add a picture of the crank.

Hi all, Hoping to confirm a part number for 6 left hand replacements. Hole spacing is 1 1/8 x 5.25 with a 2 3/8 arm. Some of the arm attachments seem to be via c-clip and others by threaded grommet. Also looking for an extended or straight crank handle. One was installed in a corner beside a door ... (cont.)

No markings present on part. Please recommend replacement

Hi experts, I'm hoping you can help me identify the replacement parts for these crank openers? I'm thinking it's likely the Pan Am/Daryl Window Crank, Product Code: 39-017. But would love to get confirmation as I need to order several replacements. Thanks much, Elizabeth

Not sure what brand I need it has one mounting hole at top two mounting holes at bottom

There are no names or part numbers on the existing crank. I ordered 39-060, the Keller window crank, hoping it was the right part. It is not. The case appears the same, but the arm is shorter on this one (~5cm) and the hole that attaches to the window arm is wider in diameter (~1cm). Serves me r ... (cont.)

Hi can you help me locate which window crank I need to purchase there are no part numbers engraved in it. Its the right side window crank that's needed. There is a screw hole at the top is in the center and there is a hole on each side at the bottom. I hope the photos help let me know what else I ca ... (cont.)

I was hoping to replace the window cranks on a few windows in a sun room at my house. I've attached pictures to hopefully narrow down what parts I would need. I can't find any part numbers or manufactures names in any of the windows or existing cranks.

hello, could you help me find a replacement for the crank that's in the pictures? Am I correct assuming it's part #39-017? would I need 33-067 to attach it to the arm inside the window since the flat spring won't do anymore? thanks! Jack

Jalousie Window OperatorMeasurements:Between top and bottom holes - 5 1/4"Between bottom holes - 1 1/8"Arm length - 2 1/2"Width - 15/16"I am in need of 6 units of each of the parts listed in the Subject l

Hello Swisko I need this crank -operator Bronze Thank you.

Hello!I'm looking to replace my awning window operators in my sunroom. Out of our 8 windows in the sunroom, I believe only 3 work OK. The rest will open but not shut. I've been searching trying to find my replacement parts. Could you please direct me to the right type of replacement operators? I hav ... (cont.)

Molded into the bottom of the housing are the following: PAT. NO. 198202 U.S. and below that 2 R.H. RD. 1963 CAN.Distance from top screw hole to bottom screw hole: 5 1/4".Distance between bottom holes: 1 1/8"Length of operator link from joint to window (center of post to center of post): 2 9/16"Wind ... (cont.)

We have 9 multi-pane and 2 single-pane aluminum awning windows from Victor Windows in Philadelphia installed in our summer cottage on Lake Ontario. (The company is out of business.) I need several new operators. The old ones have the same specifications as your Items # 39-025 and 39-026 with one ... (cont.)

Need to replace the entire white crank unit handle comes off n parts fell out

Unfortunately I see no numbers or markings on this mechanism. Dimensions top screw to bottom screw i measured as 5 1/2 inches. Looks like 1 5/16 from bottom screw to across to the other bottom screw. Hoping you have this replacement part.

The first picture is what you just sent me and the second is a picture of the old operator that does not work anymore. I received a part from you that seemed to be the right one but there is a screw attached on the arm that can not be removed, thus I can't use it. Do you have an identical part to ... (cont.)