Viewing all customer Discussions for:

Door & Window

frame is 5/16 thick. There are what look like 95-182 in the upper corners. Do you have these latches? There are also middle pins along the sides that look like the upper corner plastic pins. Do you have those?

Hi! I have a VPI door that needs a new sliding door track that has been discontinued and VPI referred me to you. I see part #80-106 matches my dimensions but I need a 10' length, not 6'. Am I able to double up the part so it reaches the length I need? Thanks!

Hello, what would be the part number for this piece? It's on the side of the casement window that supports the window on the sides. It is heavily corroded and keeps the crank from functioning. These are pella lower casement windows. I previously purchased 39-239C for the actual cranking mechan ... (cont.)

Hello,Hoping to find this Larson latch in your inventory. Pictures attached. Only think I see on the part is 20 GN.Thank You,Roger

Picture of good latch and broken latch Dimensions 4 3/4 inches long 7/8 inches wide 7/16 inches deep

Hello, Can you please tell me the part # that I need to order? Using the crank handle the window will open but not close.

Can you identify this? I need several. The square corner that the rails stop against is 1-1/8" square. The tongue that slips into the rails is 5/16" x 3/4".

Hi, Can you help find replacements for my damaged channel balances. Attached are pictures of the balances. The window has a sticker with "Series: 5000 TMF" and "H-C30-54x96". The length of the metal part is 22" Thanks

Number on the the door is PPD 2wI36.063x76.438 The roller housing is 6 3/8 inches long. The main body is 4 5/8 long. The housing is approx. 5/8 inches thick & 1 3/8 inch tall.

Hello. This balance is broken, and I'm looking for a replacement. It's 24 inches long with a stamp on the side showing 2330. Thank you for your help

This is the vinyl glazing that is inserted into the channel on old storm windows. The pictures are both front and back of the vinly. The width of the vinyl when folded flat is 5/8 inches. It is doubled and wrapped around the window and inserted into the channels. The window is inserted in the ... (cont.)

I want part of inferior stop for my window

I need a new sweep that attaches to bottom of door. Door is 35" wide and 1 3/4 " thick. The old sweep has a single kerf along the middle of it and attaches via a groove in the bottom of the door. It is made of hard plastic with 5 very flexible fins that protrude down to meet the threshold when t ... (cont.)

Sorry for the glare- I need to replace the entire mechanism. Any idea which one this could be?

cant not find any part numbers only thing on it embossed anywhere is the word China. 3 coil balance part the broke is the bottom plastic.

Hello, I ordered item number 90-072 Sweep lock. The description says it is 2 - 1/4" however upon receiving the product, It is not 2-1/4 it is closer to 3"and does not fit on my door. I think I made an error with my original measurements. The original lock measures about 2". Do you know if you carry ... (cont.)

Hi there. I would be most grateful if you could tell me whether you have these window latches in stock.

This part is from a Ply Gem window. It is a swingout window latch, it has two mounting screws on the base that attaches to the window. There are dedicated right and left hand closing latches. It secures shut by moving the handle from the vertical to the horizontal position. The part has an attac ... (cont.)

Can you identify the correct pin from this pic? this is a left I need a left AND a right.

My window sash moves all the way to the side wall of the window when it's fully open. I need a 10-inch and a 14-inch version.