Viewing all customer Discussions for:

Door & Window

Need coil spring replacement

Hello, I have this part I would need to identify and replace. Thank you, Robert

Hello, I have (2) windows with this set of balances. The sash weighed 26.5 lbs The length of the metal was 20-5/8" long. This window failed so if there is an alternate channel stamp with the correct corresponding weight I provided, I'd like to explore using a standard length. Thank you, Robert ... (cont.)

Hello, I have (1) windows with this set of balances. The sash weighed 32.2lbs The length of the metal was 26-5/8" long. This window failed so if there is an alternate channel stamp with the correct corresponding weight I provided, I'd like to explore using a standard length. Thank you, Robert ... (cont.)

Hello, I have (2) separate windows with this set of balances. The sash weighed 19.8lbs The length of the metal was 26-5/8" long. Both of these windows have failed so if there is an alternate channel stamp with the correct corresponding weight I provided, I'd like to explore using a standard length. ... (cont.)

The sliding door was installed in the Plaza Condominium San Diego in the early 1970's. Label embossed on door locking mechanism is "Door Master Manufactured by Ralph Long & Sons El Cajon Calif." Included are photos of the latch mounted to the slider, the device that hooks into it, two views of the p ... (cont.)

Looking for replacement bronze glazing for 1986 Lincoln casement windows. do you have a replacement that will work? John

Hello, I need to replace the sliding door handle and lock set. The patent # I have is 6.264.252. Below are the pictures of the multi point mortise lock and door handles. Could you please suggest the best compatible parts? Thank you

Can you tell me what mortise lock I need for the 82-086 legacy keyed handle? My current mortise lock is for a center key hole but the 82-086 is not a centered keyhole. So it doesn't line up.

Hi As above, I need replacement sweeplock that is 2 1/8" and 3/8 from edge. It locks into a face mount that has holes 3/4" apart. Can you help me out? Thank you so much and best regards. Lu

It's a model 45275

Thanks

We had this double sliding door installed and our contractor lost the hardware It looks like there is only one latching mechanism on one side, but both sides have holes drilled out. Can you tell which hardware will work and get the door to lock and close tight? Right now there is a gap. ... (cont.)

Hello, I have aluminum windows from the early 1980's that have these types of rollers. There are two per window and exist on the ends at the bottom. Can you please help me identify the proper replacement type?

I need 2 Operators as shown and 3 opposite. The straight arms are 9-1/2" to the wheel and the end section of the short arm is 4-15/16". My operator shown is stamped with S-1491-160, and the opposite is stamped with S-1491-265. 1 also need 1 beige lock as pictured on the left. I saw a discussion on ... (cont.)

These are 26-3 channel balances. We need 8 of them total. Theres also a stamp that says RN BSI F on it. These are Atrium Vinyl windows. Not sure of the year. Probably 10+ years old.

I have what I believe is on old Stanley exterior door that needs a new seal. I ordered a 58-008 prime door seal set - this ended up being too light duty for my entry door and doesn't seal. I attached pictures of my existing seals (which I should have done up front and sent them to you before I ord ... (cont.)

Looking for for this seal plastic snap the actaula dimesions are 3/8 of a inch deep 1/4 wide side but looking for something else wider that 1/4 the windows are shorter

32-4 dx cmc 11

PGT SH7700A Single Hung Window - Bottom Sash Guide I am needing a part for both side of my window. I believe it's called Bottom Sash Guide Cap. I am including pictures for your review.