Viewing all customer Discussions for:

Door & Window

Hi my name is Bob I was told to send pictures of the door latch I am trying to replace. I think it's 40-049

I measure 27 inches metal to metal and the stamped metal is 26 4.

I need the push nut for an Andersen exterior door lock

Hi there, we need to find a replacement crank. I can't find any manufacturer name or numbers.

I'm seeking a 33" Length (metal part). Window weighs approx 20-25 lbs. photos to show top and bottom plastics pieces. Milgard Channel Balance. Need 2. Photo Attached. Thank you

Hi there - my door lock is not functioning anymore. This is the text from the door: AAMA/WDMA/CSA 101/I.S.2/A440-05/08 Product Rating & Maximum Size: Class LC-PG40 2438 x 2438 (96 x 96)-SD Class LC-PG50 2438 x 2438 (96 × 96)-SD (HP) Prime Window Systems Denver, CO Product: 411 Sliding Door (X0) ... (cont.)

My center to center is 2" 3" long,1 1 1/8 wide

They all snapped off. Have a good replacement part?

I need to know which of your top sash guides is compatible with the one in my attached photos. My channel balance is a 3550 which looks like your part number S380-36. I do not know who made my windows. Please let me know if you have a compatible top sash guide. Thank you.

I am looking for some weather stripping for the bottom of a storm door. The sizing is important as well as the t-channel it goes into. I've attached pictures for reference.

I am looking for two (2) coil balances for a Simonton Window. The information on the label of my window is as follows:q012901995997010003000144/04/14 2CWhiteM(bottom line) S Bttom 2 NHS WH 00 17 550HWI32 . 813x26 . 625Please let me know if you need additional information.Thank you so much,Dani ... (cont.)

The pictures are for spring balances for my 2 36" X 36" windows. It appears that the replacements are Series 377. The channel length in the photo is 18 1/2 inches. What size should I order, 18" or 19"?

Hello, I have two double hung tilt windows. The lower windows do not stay open and I noticed the sash cords no longer have any tension. I was able to remove the channel balance and would like to order 4 replacements (one each side of the lower window for two windows). The only marking on the channe ... (cont.)

1 3/4" X 1 1/4" X 1/2"

I'm trying to replace the handle from my sliding glass door.

The latch for the sliding glass door will not raise the latch to lock the door. The inside lever is very loose and will no longer control the piece to latch on the lock.

I have Crestline Casement windows and need 2 right hand and 2 left hand operators. - They are all of the single arm variety. - The total single arm length is about 9 inches. - The body (where the gears are located) is about 5 inches long. - The operator looks identical to your 39-216 and 39-217. ... (cont.)

Looking for the sash weight option stamps on window balances. There is an ink stamp that says "26 2 JT CMC 4". Does that indicate a 2620 stamp? 9 - 13 lbs? It would make sense, I think. But I was looking for a 4 digit number someplace.

3/8 balance 30" long red tip. Can't tell how balance is attached to bottom of sash, Can't find any clips on either side. Could possibly tell more with the sash out but can't figure out how to remove it? Can you help? Window needs both balances and new weather striping and probably clips for balances ... (cont.)

Hi I have this half jalousie window door on my florida room and it has this built in jalouise hand crank square assembly built into the door that no longer works. I cannot figure out how to easily remove it without destroying it but the issue it is what product do i replace it with when I do remove ... (cont.)