Viewing all customer Discussions for:

Door & Window

Left and right corner window adjustment pieces to raise and lower storm window

Looking for a replacement. screws are 7 3/16" ctoc

Hey I called in to buy slider door lock. I'm attaching photos of the lock. Also we have a gap at the top inside of the door and didn't know if you guys sold any pieces for that. There is photos of it as well.82-218 mortise lock is what I think we need.Thanks for your help.Cheers Byron ... (cont.)

I need 4 -31" long 3/8"wide balance rods And. 4-29" long 3/8" wide balance rods They do not have a color tip butt the sliders have a red insert. The end that connects to the sliders have 4 studs on them 2 on each side 1/2" apart protruding out about 1/8". The windows are 21 years old. ... (cont.)

this is a cabinet drawer center track stop which slides into the track on the cabinet to stop the drawer from coming off. it is 1w x 3/4h and 3/4 deep

Need a complete set of channel balance for a single hung Larson Window. Markings include "3520"Thank you,Richard

Hi: Here's a photo of a nylon wheel unit from a 3-foot-wide HiLite door. What I need is the steel wheel part to replace rollers on a larger HiLite door--4 feet wide. I don't have a photo of that one. Suggestions? Thanks!

I have a window balance that has failed and I need a replacement. It is 1/2" wide, 17" overall length. It is out of a Phillips window and the marking are 15 4 LR CALDWELL. Thanks for your help. John Davis

Do not know the manufacturer but sticker in the top say warranty information do not remove s/n 213-050660

I have attached a sketch of the part. It is similar to your part number 26-226. However, the hole location on the piece I need is approximately 1-5/8" from the head. Any help you could possibly give me would be helpful.

Good Morning,I am looking for 5 complete units like the pictures above. I can take better pictures if needed. Please let me know avail. and price to ship to my home in West Warwick RIThank You,John

I have of few of these window stoppers that are Miss and we would to replace them. The windows were already installed when we moved in our home, would like to replace the ones that are missing and broken.

Hello. I have a broken window operator that I need to replace, but cannot identify. Is there any way that tyou can look a the pictures I've attached and let me know what you think the best replacement would be? Thank you. Garrett

Trying to identify what hardware this is? I have several that are broken/non functioning. Apparently these were Patriot windows from around 2005, according to the NAMI sticker. I?m needing the hardware specifically. Any help on finding replacement sill stop trim would be appreciated too! ... (cont.)

Hello. Could you please tell me which part I would need to replace our window shoe? The attached pics are installed and removed one that is broken. Dimensions are: 2" H X 1.25" L X .5" D Thank you! Tracy

This is the number on the Milgard MFG single hung windows.They are 24 inches wide 34 inches tall. MG-1 ALI CBA

US Patent 4,241,541 20755 40471 EntryGard Truth - backside 30470 L.H.

Hello, Please see attached pics. I would like to purchase a new glass patio door handle/lock system but no clue what to but that will work with current door. Hole distance on Mortise lock 3-3/4". I have tried the 3-15/16" on a previously purchase from a different vendor and the 3-15/16" did seem ... (cont.)

If you unlock window, the back outside window drops. The metal pieces shown as pic 5 looked yo be broken off. Pics 3 & 4 shown the pieces on a working window. Pics 1-& 2 show were the metal pieces should protrude crom. Can you please identfy the part so I can order 4? Need two metal pieces comi ... (cont.)

Hi,I?m looking for a pivot bar (see photos). It's simlar to the 26-396 T-NOSE PIVOT BAR, 3-1/8", without the "Tnose" and is 1/8" shorter. I have three broken and will need to order 14-16. Better to replace them all now than one at a time. Please help.Thank you.Leo