Viewing all customer Discussions for:

Door & Window

I removed the latch receiver to install a temp cat door. Now I cannot find it. Simonton sliding glass door. Just need the receiver that mounts to the frame so the door can latch. See photos

Hello, I only have 0.5 inches clearance on the window frame, the image suggests 5/8" is needed. Will Your 26-387 still work? Jim

I already fixed my tilt window thanks to you guys.. Next project is very old sliding windows (1960?) corners.. pictures .. I also need the set screws (and possibly the the stuff that goes between the aluminum and the glass.. weather strip?) The windows slide sideways and are about 3' x 2'each wil ... (cont.)

No markings, names or numbers found

2

I haven't gotten one off yet; but I can see the following numbers: 33 3 BSI NB (the BSI is at a 90 degree angle) Do you have these? Please advise. Thanks. Robb

This is for a comfort window made in 2004. I am looking for this assembly to open the window. Where can I get this?

I have an alumiun sliding glass door that needs a handle and lock. Enclosed is the information I could decifer. December 1999 we bought the house. PPG HERCULITE K 8961 0621 OR 8691 0921 TEMPERED CFR 12011H HGP The lock broke into pieces. I have bought several handles with lock.I. have be ... (cont.)

I need to replace broken Block and Tackle Window Balances. Do not know who is the window manufacturer. It is a non-tilt window and side load. Measurement is 15" and a 9/16" channel. The window has a label w Mfg Code YOM-1 Series 9500. Window H-R50 53x74 The marking on the broken one is 14 ... (cont.)

Hi, I am looking at your hanger set to repair a pocket door (Product Code: 23-255). The dimension seems to fit the roller I have but I cannot find the size of the wheel.What is the outside diameter of the wheels? I need wheels smaller than 1inch OD. Any chance you have that in stock? Do you sh ... (cont.)

Is there any parts availble for this old style lock ????

Hello, I moved into my home during the winter and in Spring, discovered the previous owners took the skylight eyelet. I have no idea who the manufacturer is (I've looked all over the frame and glass). I measured the spline, I believe its called, and it is 5/16th. The pole they left behind has ... (cont.)

Part 26-407 is definitely the part I need for my Stanek window, however can you please guide as to how to remove this type of fastener? As seen in pic it is round with hollow center. Thanks, Bill

Hello-I have a house that was built in 2002. I'm the second owner and I have wood/clad windows that need some TLC. The windows are double hung, vinyl jamb liners (beige in color) with 62A balances in them with marking of 24R or 24TG on them. I need shoes if they are easy to replace? I've researched ... (cont.)

Need to find a sash Guide that fits this size. Thank you

The right side window latch handle broke off. The one shown is the left side. Is it possible that you still have this part available? If so I would like 2 of them, or if they are left and right, I would like one of each. Thank you. Richard C

Hello I'm trying to identify and replace the bottom rollers for track sliding closet doors I do not think mine have any kind of offset due to the fact that they are three closet door systems two doors in the back and one door in the middle in the front I'm looking at your website trying to figure ou ... (cont.)

Which sash bracket assembly goes with the X-Drive Split Arm ROTO Operator #39-325? Do I need the 39-534 or the 39-535

I need to replace my balance that is 25 inches in length and has the marking 25 5 IS CHADWELL.

Hi: I'm trying to find out a sash 5/8"w x 1-1/4" window guide,like the one attached. Thanks, JJ