Viewing all customer Discussions for:

Door & Window

For the lever Product Code: 39-069, would you have the instructions on how to install one? I have to replace on that was broke off. Thank you

Toothed sprocket has that number - no others located

Photos show 3 window handles which have been broken. No one seems to know the proper model no to replace these. I'd like to see a photo of possible replacements. Also, it appears that the black plastic small box inside the handle has been partially broken in one case, remained in the fixture in ano ... (cont.)

I am trying to find the correct glazing bead to order. Please see the pictures. The one I have is 5/8" on the flattest part. The remaining lip is about 2/8" I don't know if this helps at all, but the information on the double pane glass itself reads: Dec 7 2005 761855.003 0970 u2c2 LOWE4V 557 ... (cont.)

Milgard double pane windows - current balancer is marked 19 9 GS CALDWELL. Metal channel is 30 inches long. Thank you

11600-3 C166?23485

Hello, My track needs to be replaced and I have determined that I need to order part # 80-102. I would also like to replace the rollers Which ones do I need based on the attachment I sent? If you need more information, let me know. Thank you, Frank

Stanley sliding glass doors 50215051 / 64564-001 top roller assembly

Hello, How can I convert a Capitol Glass sliding door utilizing a pull and lock bar ( 82-010 and 82-102 ) into a keyed lock sliding glass door? Door frame thickness is about 1-3/4", the frame width where I can drill and cut is approximately 1". Thank you!

I have a truth entry guard operator that needs to be replaced. I also need to replace the clip stud bracket however the one that is attached to the bottom of the window is flat and does not have an angle. Would you have replacements for this also?

I need help with ID on a part. I have double hung windows with a spiral balance and a 17/32 tilt shoe. I can not for the life of me think of the name for the metal bar on the bottom of the window frame that sits the window into the shoe.

Is the crank handle (39-114L) match the Traditional Window Operator with a 13 1/2" arm? I just want make sure I order the correct one. The handle on the old operator had a set screw which I had to drill out to get it off. I don't see a set screw on this handle. What holds it on?

Which part are you measuring at 9 1/2 inches? Part # 39-155

I am in need of parts for my Simonton windows. I need balance coils, coil covers, and pivot blocks.

I received the ordered balance S500-29 red tip, 29" series 500 spring balance. It is too thick of a diameter to fit in the track. It looks like the space is a maximum of 3/8 inches. The S500 too wide of a diameter at about 1/2 inch. Do you have one that is thinner at a 3/8 diameter. ... (cont.)

I have a single pane window - 47.5" wide X 59.5" high rough opening. I think the window manufacturer is Marvin. The existing channel window balance has 26 5 GS CALDWELL stamped on it. Would like to get two pairs, plus one of the stops needs replaced.

I have replaced all of my channel balance hardware that I bought from Swisco yesterday. I found that the top sash guides were broken on most of the windows preventing the channel balance hardware engagement. I looked on the Swisco.com website and can not identify the part I need. So, I need you ... (cont.)

This Cole Sewell was purchased somewhere between 1994 and 1998. As you can see, the outside handle is brass and the inside white. The faceplate on the outside is 6 3/4" x 1 1/2". The faceplate on the inside is 3 1/2" x 1". Everything similar that we have found at Home Depot or like places have o ... (cont.)

I looking for replacements. The armature is 11". Thank you, David

Hello, I've been looking all over for this part to hold up my glass in a curio. I would really like to know if you can help? Thank you Sherry