Viewing all customer Discussions for:

Door & Window

Hi, I'm looking to replace several of these operating cranks for a casement window. The rest of the window hardware works OK. The part says Biltbest Part 233 D.C. It is from a window form the 70's or 80's I imagine. It is approximately 4 5/8" wide and 1 3/4 deep. This one is left handed with a gold ... (cont.)

The part size is 6 1/4 (L)" x 3" (W) x 3/4" (D) plus a small flange with the staple in it. The visible glass measurements of the lower sash of the window are: W= 28.5" L=34" There are two set of numbers: U8 11L 12-87 and U7 11R 12-87 The other number is 11600-17. I need both lef

Hello, We are looking for this pivot bar for our M&W window. The piece that sticks out from the window broke off and now the bottom portion will not stay in the track when the window opens. I attached pictures of the piece that we removed that is broken. The broken piece measures 3 inches with ... (cont.)

I have a very broken coil spring assembly I'm trying to replace. The coil does not have a weight on it but they are alside Fusion windows. About 13 years old. Double hung, tilt windows. The Sash weighs about 20 lbs. There are only springs on one side of the jamb. Looks to be dual spring. S ... (cont.)

sliding door guide anti rattle

I have Milgard sliding doors. The screen latches (double sided) need to be replaced. They are black with a recessed square centrally and there are two screws. Can these be ordered from you? Distance between two Philips head screws is 2.5 inches; width 2.0 inches; height 3.75 inches; 4/8 inch thick. ... (cont.)

We have tried your pivot lock shoe 15-129, but the width of 1 1/4

I have attached a photo of the pattern I need. I need about 10 of these 33 and 3/8 inches.

Hi, I'm fixing my windows to sell the home and there is a pivot retainer missing (see picture.) I don't know who did the windows because it was done previous to my owning the house. Can you match?

need a price on this weather vane balance 2430 bs1 has 19-038 top and 15-193 bottoms

Hello, I purchased 20 springs (S400-34) and 20 brackets (17-043) a few weeks ago and am now trying to install them. Unfortunately, the brackets are not compatible with the springs. The picture of the bracket shows several measurements... but didn't show the measurement of the depth of the throa ... (cont.)

Hello! I have about 8 awning windows that were installed new about 10 years ago so not too old. The location is on the Jersey shore so sand is always an issue with the gears which I'll be cleaning and lubing (silicon spray) on a regular basis going forward based on your site's recommendations. ... (cont.)

I do not know the window type. The shorter straight side is 1/2 inch and the curved side is 5/8" from the top of the peak to the bottom.

This part is attached to the bottom of the window. It mates to the sliding part . Together they form the Pivot point that allows the window to tilt in. I need 2 of them

The lever on our mechanism broke off with the window locked shut. I believe, based on measurements of other similar windows in our home, that this is the part we need but how do we unscrew and remove the broken latch mechanism with the window locked shut or how can we unlatch it without the lever? ... (cont.)

I have Caradco casement windows but the crank/arm measurement is longer than the example on your webside for that particular part and you seem to only carry the one size. The arm itself is approx. 12". Do you sell a larger/longer crank size or are they standard? The windows were installed in 1971. ... (cont.)

501072

I just received a Pella multi-point mortise lock. But now my client needs the strike plate. I see you have one strike plate that comes close, but the holes don't match up with the two dead posts and the latch for my mortise. What should I do to keep my client's door closed?

Tilt latch photos I think we are surface mounted tilt latch Our length is just over 2.5" Our width is 11/16" Which of your tilt latches and I am ok buying a few different sizes would you recommend

Wenco windows non tilting , metal is 27" 1/2 wide cannot tell if ears on bottom piece are broken off not are like that and have rough edges where the ears would be. The stamp is 2630 BSI NL. I need 2