Viewing all customer Discussions for:

Door & Window

I need a couple of vent locks for a vinyl window. The slot is 1/4" W x 1" L. The photo shows the current one. The piece is broken at the bottom. I do not need an exact match. I can use a substitute as long as it works. I can file the hole to make it a little bigger if needed. You were recom ... (cont.)

CAN YOU PLEASE TELL ME THE PART NUMBER FOR MY WINDOWMASTER "WINDOW CHANNEL BALANCE" CHANNEL BALANCE PHOTOS-ATTACHED SINGLE HUNG NON-TILT WINDOW CHANNEL (ONLY) LENGTH = 32 IN. CHANNEL WIDTH: 1/2 IN. (9/16 IN.) WEIGHT CAPACITY (STAMP ON CHANNEL) = 3140 (23-28 LBS)

Can you please suggest which of your products will best fit to replace the handles and locks on my storm door. Thanks so very much

Good morning Customer Service , as per my conversation I had with one of your reps the other day these are the pictures to show what I have the metal frame is .5 inches wide and 16" long its stamped on the metal frame 15A if you have this what will the price be for 4 of them . If you have any quest ... (cont.)

I'm looking for a channel balance that is the following dimensions and kind. (22"X1/2"X1/2") The window is a single hung, vinyl. I do not know the brand, other than the builder spec sheet says "premier plus" on the line for window mfr. I've attached 3 photos of the balance on one side of the wind ... (cont.)

Handle screws are 5-3/4" apart

Need 2 of these surface mounted latches

The rail is 5/8" tall and 1/2" wide. The rail is 28" long. The rail has 2730K stamped on it. Thanks for your help!

Looking for corner keys for 5/16" width. Picture of existing pieces below.

Hi, I purchased a pair of 81-051 sliding glass door rollers from you. Unfortunately they did not fit. The photo below shows the roller I need. Do you stock these? Thanks!

This looks like a 15-177. Measurements appear to be the same. The metal half moon part broke on both sides of the sash as you can see in the pics. Both springs appear in good condition. Can you confirm part #. No markings listed on it. Thanks, Doug

Who knew replacing a screen would be so difficult! Hardware stores do not stock the rigid spline used on Anderson Forever doors. I'd like to order some from Swisco but want to be sure I am buying the right stuff. Installed, the visible portion of the spline on my door measures 5/16". Do all Fore ... (cont.)

I am looking for instructions on how to get at the screen door parts. I need to remove the door to replace the screening.

Greetings. I have been looking for a pair of rollers for one of our Better Bilt sliding windows. Although our rollers are brass, not steel, I believe your 16-180 Sliding Window Roller Assembly has the same dimensions and design as what we are looking for. Our white nylon platform is 1 5/8" long an ... (cont.)

I thought the part was #V6155 but I guess I am wrong. What is the part number for the channel ? Shoe ? Are the part numbers different for left and right ? What would cause the bottom window to not stay open ?

Here are the pictures of the rollers I need for a steel sliding glass door. Do you have any suggestions for replacement wheels. I need to replace three doors

I NEED THE CAST CORNER FOR A FIXED PORCH WINDOW FRAME. IT MEASURE 1.375 IN LENGTH 3/16 THICK AND WIDE WITH SCREW HOLES ON BOTH SIDES OF L SHAPE. Attached are piece of half the L shape. Thank you. John

I was told this was a Gapco storm door. I hate to throw it away if I can fix it. What do I need for this repair?

I need to replace the box that holds the sash cords on an Andersen window. The numbers on the box are E41 9-22 9-77 (from what I can tell). It is on the left side (looking out the window). What set do I need? Thank you, Pat

3 more photos to follow door - 1 5/16 lock screws - 5 3/8 on center lock face width - 3/4 handle screws - 3 15/16 nor markings on the lock Jeff