Viewing all customer Discussions for:

Door & Window

Hi. I am looking for replacement rollers. I was looking through your site and I found Product Code 81-164. It is so similar to what I need. Wanted your opinion before I ordered. Below is a picture.

One side has following Canadian Patent No 919213 Patented 1973 Other side has following: Patent No 3,596,954 Measurements: Height without tabs: 2 5/8" Height with tabs: 3 1/2" Width without side tab: 7/8" Width with side tab: 1 5/16"

29" metal frame, looks like '''26 5 HO Caldwell''' printed on frame but kinda scetchy

Hi, I have Silverline Swinger windows missing channel balances. The full window hight is 51 inch. Can you please advise what size balance I need for these. Thanks --jsd

looking for replacement operator left side. Centerline to centerline of arm is 9 &3/8".On the arm is printed ULTRA. Also on arm above the ultra is an open circle that is open on top. Arm is 1/2" wide at end and 5/8" wide towards gear. Operator is flat mounted with a choice of 8 mounting holes. It ap ... (cont.)

Is this skylight operator available with the angle drive and support link on the left side of the casing? I am replacing an worn out unit and want to avoid modifying the skylight frame.

I am looking to replace some sliding door pulls. The one I took apart has the following pieces: DNS Industries 12 Inside Pull Standard DNS Industries 13,23 Outside Pull Standard The screws are 6.5 inches apart. My current handle is 9 1/2 inches. What do you have available for replacement? I hav ... (cont.)

Pivot shoe shown in photo should have a blue cam. 2.25 inches long, 1.25 inches wide, 9/16 inches thick 590CSB stamped on side.

We are adding shutters to Anderson casement windows and need an extension to allow the windows to open. Will the #39-157 extension with 11/32 spline fit the Anderson hardware???

I am not sure of the corresponding part I need to purchase,your help is appreciated. The window is Anderson. Thanks, Patrick

S200-32 did not work out. Need correct balance ID

Please help me to identify this part o a replacement for it. Thank you.

we are builders in FL and have a home that has Jalousie windows. There is a part that is above the crank to open and close the windows that is also attached to one of the support arms. It is made of plastic and we have many that are broken. I have attached a picture of this part. I can take more ... (cont.)

Good morning, I am looking to replace all my window channel balances. I have varying window sizes and I am not finding a stamped code to help me with classifying each window size. I looked all over this thing. I think I have my top and bottom config correct based off your photos. ... (cont.)

Would you have any of these storm window

Hi

Can you tell which channel balance I need to buy. It is 1/2 inch wide and the aluminum is 29 plus inches long. Please refer to the attached photos.

Gentlemen, My vinyl windows are dated (on glass mullion/spacer) 81 (1981). They may have been sold through Sears, but I can't be certain. First attached composite picture shows my existing hardware, and a detail of one of your pivot shoes that has the same cam slot dimensions as my shoes. ... (cont.)

Dear Sir or Madame: I am re-screening a number of the Andersen window screens in our house. I saw in the description of the spline Product Code: 59-250 (250-Foam-Screen-Spline/pd/Spline/59-250) that it is the size often used to replace Andersen metal spline strips. The question I have pertain ... (cont.)

I received my order no problems. I do have a question about the In-Swinging Door Handle Set, 1-3/4" item 40-028. The part fits but doesn't spring back after turning it when opening the door, the part we had on there before did. Is there another handle that springs back to standing position? I'm ... (cont.)