Viewing all customer Discussions for:

Door & Window

I have remove one of the sash balances from a double hung anderson window I have. I have not included images, since the numbers are to diffucult to photograph. One side has the following number: C23 6#23 10-85. The other side has 11600-3. Can you please tell me which replacement part I need? Thank y ... (cont.)

this is an older sliding glass door that is missing the interior handle and locking mechanism. The exterior handle remains. Probably a standard sliding door for the 1990's.

I'm trying to determine the correct sash replacement piece to order. Can you help? I The channel is 1/2 inch x 28 inch long. It has a marking of p A2730 on the piece. I also have another channel that is the same configuration but has a heavier dual spring ( small spring is inside a larger on ... (cont.)

The overall length 30" X 1/2" width on the balancers, the markings are 2840 followed by a backwards D,and "B.S.I". the plastic guide parts are all missing, I have no examples of what is needed to get these windows working. Any help would be appreciated... The home was built in the late 80s and is ... (cont.)

Hello, I have window locks to be replaced and they look like on this attached picture. Do I need Window Lock with Alignment Lugs, 2-1/16" Product Code: 90-077A Face Mount Keeper, 1" Product Code: 90-237 Please, advise. Thank you. Michael

Is there a way to retro fit screen panel pulls without pulling the spine and re-screening?

Dear Sir or Madam: I am looking for replacement tilt latches. I have attached pictures for your review. The product is plastic, measures 2-5/8 x 11/16.

Do you carry the plastic cover for locking handle for casement windows? I just purchased the Truth folding crank and handle set from you for several of my windows and may need several of those in the future as well, 39107FK.

My indoor latch is broken and I need to replace.

replace my part in the attached photo? The measurements are the same. The wheel is different. Should I buy the whole assembly or just the lower piece as a replacement? Thank you! Marcus

I need help identifying this corner bracket. any suggestions or help would be great. Also do you have .230 foam spline in rolls of 100 feet? All I see is 25 feet. Thank you kyle

Length 35 5/8" Width 1 7/8" Fits door that is metal on outside and wood on inside Purchased 25 years ago- no markings or stamps

Need rollers for sliding door. Sliding door is 48" w by 78"high and was new in the mid 1960's.

I need 2 window balances the same 27 inches long with the plastic pieces. The numbers are on the one that I sent to you. Thank you Mike's property maintenance

I am looking to get a crank extension for an Andersen casement window. I only need a 7/8" extension. The one I see on your site says it's 5/16" and I'm pretty sure the Andersen cranks are 3/8". Will this one work, or do you have any short 3/8" crank extensions? Thank you.

Here are 3 pics See last for size of opening needed for insert --- a no. 2 lead pencil Plus a sample of what looking for Need w/s for both sides Just under 80 inches on each side Thank you

Hello, The attached image has a picture of part of the lock that I have. The measurements are length = 7 1/8, width = 1 inch. Is this the same measurement for your Mortise Lockset Heavy Duty Knob Product Code: 40-119 lock. I need to purchase this complete lock set but the measurements must be the s ... (cont.)

I need a pair of the tilt latches (see picture). I have included a picture of the bar code on the window. Thanks, Jeanie

I am trying to identify correct balance needed. ANDERSON Window. Approx 29 wide by 45 high. Only markings on balance is 11600-17. And bottom right has C19 6#23 6 85. I need to purchase

THE NUMBER ON MY BALANCE IS C5 6 23 670 I DO NOT SEE THAT NUMBER ON YOUR WEB SITE I ALSO NEED THE TOP PLASTIC PART OF THE WINDOW WHEN I WAS REMOVING IT TO GET THE BALANCE OUT I BROKE IT THE GLASS SIZE IS 16" HIGH AND 32 3/8 WIDE IF YOU COULD HELP ME OUT WITH THIS IT WOULD BE GREATLY APPRECIATED ... (cont.)