Viewing all customer Discussions for:

Door & Window

3 15/16" center to center mounting holes. Door is 1.5" thick Need 5 sets.

I need to find the correct replacement for my alcoa windows. The piece is 33" long and is stamped with a 2230 on it.

See attached photos for markings, 27" length (of metal portion) 9/16 by 9/16 27D HC5 CMC 45

seems i've looked everywhere to find a replacement. research shows correct handle is anderson #0532308, would your handle work? thank you! gary

I have non-tilt sliding windows with 27" channel balances (I think). They have been non-operational since I purchased my house and I dont have any knowledge of the make/model other than "IWC" logo on the latch. I tried to re-attach the balances, but they won't stay attached. It feels like the spr ... (cont.)

The 55-180 looks like the closest match to what I need but I need it in bronze? Can it be painted?

Hey Guys, Thought I would run this one by you all. Sorry I do not know the manufactures name on these. There so old everything has worn of off or faded. These lock the windows down when the pin on the glass panel is rolled closed. They are 3 panel jalousie window. Thanks for any help or id ... (cont.)

I'm looking for a replacement balance for an anderson double hung window, circa 1975. The attached picture shows the only identifiable markings on the balance. Please help!

Hello, I have a couple of windows that I need to replace the snap in trim on but I cannot match the profile to any listed on your website. So I would like some assistance in matching up the trim or choosing an equivalent if I could get some please. I can snap a picture of the profile with a referenc ... (cont.)

I have an atrium wood door. The lock was frozen and broke. I need a replacement for it. Do you have one. The door is 15 yrs old it has windows on both sides of door and glass is same size as door. Thank you Anthony

Screen door attached to republic windows and doors sliding glass patio door. Label on door reads several numbers. I attached a pix of the label on the door. Need handle for the screen door. Thanks, Yolanda Cambridge Homes, Republic Windows & Doors

Integrity Screen Pin Replacement markings on window: IGCC CBA, IGMAC CIG-1, 3-98 I purchased part 70-219 but those didn't work. Thanks

Hi guys, my crank assembly is broken, unfortunately I do not know the manufacturere of the frame. I just stumbled upon your website and was hoping you could take a look and see if you recognize is without taking it apart.

Hello, I am trying to replace a sliding glass door handle set with 4 1/8" screw holes in aluminum or white. Do you have anything in stock that would work? Thank you. Donna

Hello, I need to replace my ROTO cranks for my four crank out windows. I've attached the pictures for your review. The measurements of the outside of each casing is 5.5"Wide x 1.7"Deep (at the widest point). Any assistance you could provide would be greatly appreciated!! Thank you, Jeannett ... (cont.)

Hi - I'm looking for a way to lock my in-swinging storm door. Would the 40-039 deadbolt work for this?

Hi Swisco! Very excited to DIMyself! Some questions before I purchase the parts... 1. PIVOT SHOE. How do you know when a pivot shoe should be replaced? All are old but seem to be working fine. Please see attached image and kindly confirm I should purchase Product Code: 15-111 2. COIL SUPPOR ... (cont.)

I have these snap in rollers..metal wheels...although the top ones are nylon..that look similar to what I found in your catalog, except the flat tabs on the side dont have any holes like the ones you have pictured. There were no screws holding it in, just the lock tabs on the side. I live next to ... (cont.)

My home was built in late 1967 & early 1968. All windows are Anderson with wood frames. I have cords broken on both balances and I'm not sure which ones will fit this window. The ID on the balancer is faint but appears to be CC 7 27 0. The frame outside measurements are 31 7/8 inches wide by ... (cont.)

Hi. I have Caradco windows in my sunroom and one is missing the crank cover and the bottom piece of window framing. The inside of the window is 19.75". I see crank covers on your website but I would also like the trim piece to cover the entire crank assembly.