Viewing all customer Discussions for:

Closet

I need 2 each of theses including the adjuster screws and metal insert the ball point pen is pointing to.

Looking for replacement roller assembly for our sliding glass closet door(s). The only additional information I have is the roller itself has DWB~38, S&S Bearings, stamped on it. If available, I would want 4 pieces.Thank youJack

do you have a replacement for a COX 21-717 21-767, believe it to be concave and sending pictures of rail as well in order to confirm. would like with BB if possible.Thank you in advance. Ildiko

the mirror closet door bottom track needs replacement. it looks like some of your parts, the most important thing is the- 4" wide.

missing the other sliding door roller to hang mirror

We purchased a home that has a Stanley/Monarch bypass mirrored glass closet door system. It is missing (1) upper 48" track. Track is 3 3/8" wide, 1 1/2" deep with 1 1/2" between rails. Toll free number on sticker no longer works; all numbers associated with the door system is at the bottom of the s ... (cont.)

I need new 2 top and 2 bottom pivot brackets for my doors. I also need 2 top and 2 bottom pivot pins that will fit the brackets. I prefer not to remove the track but can if necessary. No manufacturer but cardboard glued to inside bottom of doors and one caution arrow. Please advise. Thanks ... (cont.)

Hi! I'd like built wardrobe in my garage. Only instead of glass, I want to use MDF 4 mm. What do I need to buy? What are the top and bottom guides? What are the top and bottom rollers? What handles? Help me please!

stanley/monarch mirrored unit 60"Lx3.75"w acurved front fascia

The part captured in the picture above seems to be broken. The brand is Stanley and the number on it is 4050. I have tried to find it at Home Depot or Lowes but have not been successful. Do you have it?

I purchased a home and two closets have mirror sliding doors. Apparently some of the rollers were replaced with convex wheels and the doors easily come off the guides. I found one wheel tat apparently is the original wheel and fits perfectly in the groove and it is a flat and solid nylon wheel. (Ple ... (cont.)

Monarch lower track similar to deisel 23-271 59" lower track swiscoMonarch Chatsworth California project 835?49. 835051c #1983. con report3220

Hi, I am trying to refurbish two sliding mirrored Stanley closet doors. The lower roller assemblies have a number 17-4264Y-000 on them, I would need 4 of these. The upper roller assemblies have a number 00-5024 on them, I would need 4 of these. Do you have them or a replacement for them. Thanks, Jim ... (cont.)

I need the adjusting pin (shown in picture) And the spring and plastic retaining clip (pencil pointing to missing retaining clip) in the second picture.

The door pin cap is broken, and the only parts I have are thebroken cap and the spring. I also need help in installing parts into an existing door.

Please see the below attached photo of the bottom guide on my bypass mirrored closet door.The guide is broken and I need to replace it. Can you please give me the part number and where I can obtain it? Thank you in advance for your prompt attention. Bottom guide on my bypass mirrored closet door- ... (cont.)

Do you have this item or anything similar with a 1/2" or 3/8" roller?

Can you identify for replacement?

DSH 20121 on both parts3870 is a pic of the original parts to a mirrored sliding door. I ordered 23-026 & 23-027, but in pic 3925 & 3926 you can see that the tab that hooks in the top and bottom of the door is out 1/2" original is 1/16.Can you help me to identify the original pieces so I can ... (cont.)

house built in 1990s. wheel diameter is 3/4". rail width is 3/4".