Viewing all customer Discussions for:

Closet

The wheel appears to be 15/16. The bracket it 2 and 3/16 long and 9/16 deep

Need all 3 parts shown in photos. 2nd photo need the part connected to door only No names, numbers or markings

Hello could you please assist me with getting the right track. I need to replace the floor track. It is a Stanley mirrored bypass closet door. There are two doors. The opening is 58 3/4. Thank you!

The length is 5 1/2 inches including the plastic cap and metal hexagonal base. There are no markings. Will send more detailed pics if needed.

We have a Breckenridge RV with D&W Industries Tri rolling mirror doors. The design was flawed from the beginning. Doors are way to heavy to carry weight from above. I wish to replace all the parts, top rail as a guide system, and bottom rail to carry the weight. Any suggestions would be appreciated. ... (cont.)

My cousin lives in Radnor, PA, and I am helping her replace broken hardware on sliding bypass closet doors. This is a then-modern-style 1950s custom house with many built-ins, fixtures, and hardware from that period. There are perhaps 18 sliding, bypass closet doors with unusual roller assemblies ... (cont.)

I have been reviewing several submissions for people trying to find replacement bottom track for Monarch closet doors. I have looked at several of the tracks that you have recommended and several appear to match except for width measurement. The 23-270 looks like it would match except the width on ... (cont.)

sliding mirror door for a bedroom track 2 1/2 ft by 96 inches is 8ft longsliding mirror doors i need the track for it 2 1/2 ft by 8ft

Please show me steps on how to install and the exact position of bottom guides on each mirror door. Do I remove doors to install bottom guide? The top roller guides are OK.

bypass door 3/4" offset 3/4" round edge wheel made by sterling originallyI need 4 of theselooking at other wheels that are round edge mine is not AS round and wonder if your 23-003 would work?

Hello, Can you please help me identify and get pricing and availability on this part?I need 10 of them. Please let me know when you can. Thank you.

What I believe I need are the pivot guides and guide pins for National Bifold Doors louvered metal doors. They both appear to be around 4 2/2 inches long. The pivot guides appear 1/4 inch wide while the guide pins appear maybe 3/16 inches wide (or vice versa, the guides that slide are the smaller di ... (cont.)

My handyman didn?t completely get the idea of bifold doors. The pivot he put in works great, but no track. Can I buy the track and pivot hardware and install it to the side without dismantling his work? Am including photos. Please note that he built the door with little clearance, so the track can? ... (cont.)

Looking for a 60" satin gold colored top track. My track is different looking then the one shown on your site, part # 23-245. My track measures 2-11/16" across the top that mounts against the ceiling, 1-1/2" between the roller guides, and the facial side is 3".

I am needing a adjustment roller for a closet door from independent mirror industry it goes on the bottom of the door to roll in the track and to adjust

I need to know how to get this off

We put in new metal pivot rods in our bifold doors, is there any way to level the rod up and down, the bottom left rod needs to be lower st stay in the guide hole....HELP

Please tell me the diam of back plate and does it secure with one center screw?

I have a monarch sliding mirror doors on my closet. I'm trying to figure out what hardware i need on top and bottom of the doors so that they can be mounted on the top and bottom rails. See the pictures. Thx

Hi i just received my 23-225, roller assemblies to replace my AN 34124 for my mirrored sliding closet doors. They measure the same however I noticed that the old AN 34124 assembly has 2 protruding metal inserts to insert into 2 openings on the bottom of the closet door to secure the housing but the ... (cont.)