Viewing all customer Discussions for:

Closet

I need replacement door mirror roller. The one I purchased was the wrong parts. I going to send this parts in for refund today. -Thien

HOW CAN I REPLACE 23-041 FOR ACME 4011 4012

We are looking for parts to secure bifold steel closet door by Benchmark. Most likely need to replace missing spring and cap to fit the track. The pins are about 5 1/2 inches or 14 cm long (a quarter inch or 6mm in diameter). Another spring was 2 3/8 inches or 6 cm long (1 cm diameter). The track ... (cont.)

I am missing two of these bearings for a set of 9 ft mirrored doors. Thet are heldin by ridges on the outer edges and a single clip. The manufacturor sticke is uploaded as well looks like Buchmin industries.

I recently bought 2 replacement bottom rails from Swisco for my old Monarch doors which worked great (set into the new tiled floor so they are flush) but I found when I took the doors out I also need the top guides? (not sure if that is the correct name) They are kind of an 'H' shape, made from ru ... (cont.)

The bottom Track is 3.25 inches wide overall and the distance between the spines that the concave wheels roll on is 1.75 inches. The track is 47 inches wide. Can you help me replace this track?

I can not find the pivots that go in the track for my bi-fold doors at this senior residents community. I have 90 units with 5 of these doors a piece and would like to be able to get parts for them. There are no markings on any of the pieces. Thanks,

Hello! I have a Stanley 4010-2 door roller that the tabs on the sides at the top have broken off. See attached picture please. Do you have a replacement in stock? Thanks! John

I need 4 sliding door guides for a Home Decor Innovations mirrored closet door. Thank you for your help.

Hi! I feel like this top slide guide (23-130, referred to as "the guide" hereafter) is the part I need. The pics show this original part is an ACME 2066 (US PAT. 3536120). They are 4" long and the track is 1" wide. I actually have two, 4" long springs on my doors, as opposed to one larger (23-13 ... (cont.)

How do you adjust to level them.

Dear Customer Service: I am looking to restore and repair a set of metal bifold doors that were installed in 1979 in my apartment. It

We have ordered Sliding mirror door top roller #23-222B. However, it does not match the original one. Therefore it does not fit properly. Please see attached photo of the original roller we have so that we can exchange with the correct one. I am looking forward to hearing from you as soon as pos ... (cont.)

Product Code: 21-078 Is this easy to install? The previous spring and wheel came off but the pin Is still in the door. Your video was helpful, but only one piece fell out so I would like to avoid having to remove the entire closet door. The bottom left pin that slides, the spring and bottom piece ca ... (cont.)

markings on hardware are HDI abd 4050J. I purchased from Lowes.it is similar to R20121 roller guide but not eactly couldnt use this one.

I'm sending you a picture of the part I need .

I am looking for this wheel assembly for a HomeDecor innovations Safety Morro door. I am in need of a replacement

Hello, I'm not sure that I have this right. I think that I need part 23070. My bracket is 2 7/16 tall like the 23070 and the roller is the same thickness (5/16).But my roller diameter is only 1 1/4 ", I'm thinking that this would not matter and could be corrected with the adjustment screw. I can ... (cont.)

Need replacement for assembly pictured- might be your #23-041??? Thanks in advance for help...

I need 4 of these wheels. They are 1/8" wide and 3/4" in diameter. Can't find them anywhere. Guessing they are from the 1980's when the condo was built. Can you help? Thanks much! Mb