Viewing all customer Discussions for:

Closet

these brackets hold the pivot pins and hold the mirror to the frame on a bi-fold mirror door, not a good design due to the weight of the door as you can see this one broke so I expect them all to break

I am attaching the photos of my metallic closet bi fold door's hardware. Top pivot : refer top pivotphotos 5 inch long, 1/4" dia with a plastic washer or cap to hold the pin top and bottom of frame (on a door- See photo top- 8) And a two metal push nuts with cuts to hold the pin( photo no (1,2 ... (cont.)

Hi, these are the lower rollers, and the wheel has not turned for so long that it has been shaved out of round

I recently received a bottom track for closet door wjhich is too narrow (2 5/8") ( 23-240 ). I am looking for a wider version of the track I received and aslo wish to return the 2 5/8" track. I do not have a measurement at ths time but I believe it is 3 5/8 or 4". I do not see any wider track in you ... (cont.)

No other markings visible. Roller wheel for closet bifold mirror door.

Hello, I wanted to know if the parts in the "how to install bi-fold closet door pins" youtube video are compatible with my metal bifold doors. There seems to be a larger opening where the clips clamp onto inside of the door compared to the one in the video. Your expertise is greatly appreciated. ... (cont.)

the bottom rail was rusted. the photos show the top and bottom of the door. the rail was 71in long

Hi - I have Slimfold model E bifold doors installed in 1984. Will I be bale to get bottom and top pivots for it, since the current one is broken. Thanks

Hello Please see the attached pics and let me know if your 23-215 would work for me. My measurements are 2 7/8", 1 9/16" and 1 5/8" , instead of your 3", 1/9/16 and 1 7/8" Also, my brackets have DNS stamped on the metal, and DNS and DNS 1H-0414 stamped on the plastic guide. Thanks Ron ... (cont.)

Do your tracks come with 1. screws, and 2. Directions on how to put them in?

Hi - Am puzzled how to remove these sliding by pass doors - have tried releasing the bottom rail plastic guide and then tilting the door outwards from the bottom to supposedly release the top roller - but the top which has the 23-027 rollers won't seem to budge - the top roller on the outer door in ... (cont.)

This plastic piece fits into the track of a bi-fold door and the pin of the lead door fits into it. I do not have the exact measurements but it is approximately 3 " long by 3/4 wide

I had 2 Stanley 36X96 Monarch Prism 321 mirrored bifold doors installed in a closet in my home in August, 1996. The bifold doors are becoming very difficult to fold open and straighten out to close. The track wheel is broken on the one door and the same is wearing thin on the other door. Can I re ... (cont.)

I am looking for a replacement for this bifold door pivot bracket.

I have a Monarch Mirror Door and one of the wheels are missing. The door is over 20yrs old but in good shape, can anyone tell me if or how I can replace it?

Replacement rollers for mirrored closet doors.

Part is for a closet folding door, unfortunately no part nos. or names.

The guides are flexible with an odd shape. They fasten to the tops of the doors and they keep the doors centered and sliding smoothly inside the top rails or tracks. They bear none of the door's actual weight. Over time, they deteriorate from flexing and perhaps loss of suppleness. ... (cont.)

I've got an "oversized" rough opening that has jamb installed. The desired bifold has a gap on both sides and in the middle. Is it acceptable to use a "stop" i.e. Molding at each jamb side so that when I adjust the door in the center the gap on each side is not visible ?? Opinion would be appreci ... (cont.)

I see that your 23-510 track should fit the door I have but my doors are solid oak raised panel and I believe they weigh more than the 30 lbs. Also I would prefer in brown. Can you help?