Viewing all customer Discussions for:

Closet

I have a 1940s era cedar closet with doors that roll on an upper track. One of the wheels on the hanger fell off, and I cannot find a replacement anywhere. I am looking for a wheel that is 1/2 inch diameter and the bracket is flush, not offset. Do you have anything that could be a close rep ... (cont.)

I am a little confused, you show a pin cap 21-108 along with the 21-402 track in many of your suggestions, but you mentioned that this cap will not work with this track. Which track will the 21-108 cap work with? I am replacing all of the pins and tracks on a S376305 door. closet opening is 5 foo ... (cont.)

My bifold doors uses a stanley 2819 part to secure the top of the stationery rotating door ... do you have a replacement

I need a lower closet door track. the track is approximately 3 1/2 inches wide. Two doors slide on it. Im not sure if I need the 23-272 or another model. I can't get the pic. to load onto my portable computer but have pics on phone. Thanks for help. Tony

I am looking at bifold door hardware and I am wondering if some of the hardware is made out of aluminum. Like for example 23-114, 23-112, 23-139, 23-135, 23-506. And I am wondering if this piece, 23-312 is made out of some sort of steel or not.

I have 3 large panel wood closed doors. Do tracks come in 3 tracks. Closed is extra tall. Thank you

Hi, Please see attached pictures. Do you have this type of rollers? Thanks, Ken

I am looking for the base plate for a pivot pin matching 23-113. 23-301 appears to take a geared pin, not a smooth one. Will this part work or do I need a different one?

Is this track made out of aluminum or steel or stainless steel? Or if none of these what is this made out of?

Looking for bottom guides for wood floors for sliding shutters needing to keep a min. of 5/8 " to 3/4" spacing between both doors to allow for clearance of shutter pull rod.

Hi there, I have been trying to replace hardware for one of the closet, we have at house. I could see that I can use 23-086 for replacement part for COX 21-717 21-767. I need to find a replacement part for Cox 22-702. I have attached few pictures for it. Could one of you please guide me to find ... (cont.)

I see the top guide 23-044 (which is what I have) but mine rattles a bit with use during sliding. Is there a roller option that can securely position the door in the top channel and cut this noise out? Mine is probably 30 years old but in good repair and not broken (upper channel still measure ... (cont.)

The roller for my shower door is broken. Would like to purchase two. Writing on roller says, "Allen-Stevens Corp.", A-S 3937

I am having problems finding this Series bracket. As you can see the end part is broken off where the kid goes in. Can you help me locate this

Hello, I have a Benchmark metal bifold door from probably the late 1970s. All the pins (three ones most like your 21-044 and one like your 21-002) seem to be intact but I do not have any of the tracks or brackets required. I have never hung a metal bifold before so I am not entirely sure how they wo ... (cont.)

Customer Services: I am looking to replace the rollers for my wardrobe doors in my house. I was looking to just slide the rollers out and replace them to the current fittings:Do you have anything like this? I know I saw a product but will I be able to replace just the roller from this part: ... (cont.)

Hi, What are the part numbers needed for the top and bottom pivots for steel bifold doors?

Seeking the following Top Roller Guide Part - Qty - Unknown Bearing is riveted to the bracket at one end. Kilian Bearing with 1" OD and a .210" Width. ID is unavailable due to the rivet. Bracket measures 3.103" long,.994 Wide and .55 Thick. Has an oblong Hole thatmeasures1" long and .250 wide ... (cont.)

Hello, The rollers on my closet door have broken and I am looking for the correct replacement. After searching your website I think the closest replacement would be the one with this link:Mirror-Wardrobe-Door-Roller/pd/Sliding-Closet-Door-Rollers_Guides/23-064 Is there a better opti ... (cont.)

I am looking for a replacement closet door roller. As you can see my original hardware is mortised into the the door frame. Unless I can find the exact fit I would prefer to replace only the cartridge with the roller and just slide that into the existing housing. Do you think the roller from your 23 ... (cont.)