Viewing all customer Discussions for:

Closet

Looking to replace cox door hardware 21-717/767. I have reviewed your earlier posts and the 23-086 is mentioned in all, but some your mention the 23-070 and here you mention the 23-081. What's the difference between the 070 & 081. Also, the length of the bracket is 2 7/6. Would you tell me the spa ... (cont.)

I have older Benchmark doors and I need a couple of the sliding bottom rail pivot bracket. The part that the bifold pivot pin goes into. There is one on the top rail that has a place to screw into so the bracket can be used as a non-moving hinge bracket.Not sure if the same bracket is used as a slid ... (cont.)

Looking for a replacement track for Bypass closet doors - closet opening in 46 inches?

Can you advise on the difference between the following two rollers you sell. 23-070 and 23-086? The one I have need to replace is a COX 21-717/21-767.

I have several doors that are swing door going into baths and closets that have a ball with a spring underneath. I have attached a photo. some are missing.

I have Stanley bifold sliding wardrobe doors (mirrored). I need at least four thimble like cups on which the doors sit - top and bottom - I don't know the name of these cups or part numbers. HELP " Kevin.

I am trying to replace the slide glider in my bifold door but it will not pop in

I need (2) 48" of this. Please let me know if you can match this. Thanks, Ivan

Hello My doors Im guessing are 50 years old. They do not slide in the tracks very well. I saw some parts that look very similar on your website. Id like to replace the track as well. Can you tell me exactly what I need to order so I can replace the track as well as ALL the components that hel ... (cont.)

Can't find replacement roller anywhere. Images attached.

Is the lip of the this pin cap supposed to be positioned inside the upper track? On some of my Leigh TruVu metal bifold doors, the in caps are set that way; and for the rest of them, the lip is below the track. Before adjusting the doors' hardware ,I'd like to know if I need to slide the lip of thi ... (cont.)

I need to replace the wheel on my closet door. The existing wheel is a STANLEY UK PAT GB2321661B

My home was build in 1973. I am not sure if doors are original with home. I believe they are. I will need 8 of them.

Hello and hope all is well. Can you please help with the adjustable height dimensions for part 23-044? Best Regards Don

I need a 48 inch lower track for mirrored doors . The glide is a bypass type part number 23-215. Which track do I order.

I would like to locate a couple of wheels for the mirrored closet doors made by Contractors Wardrobe. The ones (wheel housings) I have seen so far on Swisco do not seem to be exactly the right size. The bolt holes all seem to be a different spread than what I have. I would of course desire only th ... (cont.)

New sliding doors and hardware. The rollers are #AN34124. I beleive they are the same as 23-225. The doors are very hard to open and close. It seems that all the weight is on the rollers and they drag on the track. When I lift the door up they work, but when putting door back down, problem is still ... (cont.)

My metal bi fold doors I think have some worn parts. The one in bathroom get messed up occasionally and I have to put back on track. The spring is bent and the bottom plastic piece looks worn. Looks like I need one spring, maybe a few bottom plastic runners or what they are called. Maybe a end stop. ... (cont.)

Hi The pictures are from big closet doors with metal frames from an apartment built in the 1980's. There is another one that looks the same but has two rollers to hold the heavier mirror side. These doors are big, 4 x 8 ft. The hardware clips into the metal frame made of tube about an inch sq ... (cont.)

It has 4 wheels. The axle to axle measurement is 2.5 inches The slot opening for the mounting bracket is 1 inch under the name "Acme" . The numbers above are more difficult to read but my best guess is 301001 The widest width across the middle of the open sided bracket is 1 inch. (You guys m ... (cont.)