Viewing all customer Discussions for:

Closet

Is the lip of the this pin cap supposed to be positioned inside the upper track? On some of my Leigh TruVu metal bifold doors, the in caps are set that way; and for the rest of them, the lip is below the track. Before adjusting the doors' hardware ,I'd like to know if I need to slide the lip of thi ... (cont.)

I need to replace the wheel on my closet door. The existing wheel is a STANLEY UK PAT GB2321661B

My home was build in 1973. I am not sure if doors are original with home. I believe they are. I will need 8 of them.

Hello and hope all is well. Can you please help with the adjustable height dimensions for part 23-044? Best Regards Don

I need a 48 inch lower track for mirrored doors . The glide is a bypass type part number 23-215. Which track do I order.

I would like to locate a couple of wheels for the mirrored closet doors made by Contractors Wardrobe. The ones (wheel housings) I have seen so far on Swisco do not seem to be exactly the right size. The bolt holes all seem to be a different spread than what I have. I would of course desire only th ... (cont.)

New sliding doors and hardware. The rollers are #AN34124. I beleive they are the same as 23-225. The doors are very hard to open and close. It seems that all the weight is on the rollers and they drag on the track. When I lift the door up they work, but when putting door back down, problem is still ... (cont.)

My metal bi fold doors I think have some worn parts. The one in bathroom get messed up occasionally and I have to put back on track. The spring is bent and the bottom plastic piece looks worn. Looks like I need one spring, maybe a few bottom plastic runners or what they are called. Maybe a end stop. ... (cont.)

Hi The pictures are from big closet doors with metal frames from an apartment built in the 1980's. There is another one that looks the same but has two rollers to hold the heavier mirror side. These doors are big, 4 x 8 ft. The hardware clips into the metal frame made of tube about an inch sq ... (cont.)

It has 4 wheels. The axle to axle measurement is 2.5 inches The slot opening for the mounting bracket is 1 inch under the name "Acme" . The numbers above are more difficult to read but my best guess is 301001 The widest width across the middle of the open sided bracket is 1 inch. (You guys m ... (cont.)

I am looking for roller plastic part of this assemble

This is a broken piece of a closet track guide that slides on the bottom of the closet tracks. It states Cx 21-022 Pat Pend on white plastic. The closet has two pieces on the bottom sides of each door. Would like replacements.

This is a sliding glass mirrored closet door upper roller. It is 4 and 1/2 inches from the top of the roller to the bottom and about 1 and 1/2 inches across. There is a number on the side 20121.

Help!!!!! I am in need of the bottom track for our Monarch Oak Mirror door that goes on our bedroom closet. The length is 71 and a half inches. Total width of the track is 3 and one quarter inches. Each door is 3ft. 1 inch. The attached pictures are of the railing and the rollers. I hope that the ... (cont.)

I need to know what part replace this top roller ...OS 20121

I saw these 3/4" finger pulls on your website. how close should they be installed from the door edge? Gerhard

Hi, wondering if you can help me? I have 2 closets with Cox mirrored bi-fold doors. One set of doors is missing the top guide wheel/roller, the other closet door is missing the lower guide wheel/roller. Do you have instructions on how to repair this and do you sell the wheels? Thank you, Gail ... (cont.)

Hi Swisco! Attached are pictures of my mirror door rollers. The outer piece is stamped 4012 and the inner piece is stamped 4011. Do I have to buy the whole roller or can I just buy the plastic wheel which is the only piece that broke - the ridge/lip that hugs the pin that it's attached to broke off. ... (cont.)

This is the wheel track for a sliding mirrored closet door. It is a little unique because it is round on the bottom (see photo). We used to get them from HD but they don't sell them anymore. Can you help me find this please?? Thank you!

charmac inc is the company stamped with patent # 4850145