Viewing all customer Discussions for:

Drawer & Cabinet

Can you help find a suitable replacement for the two part bracket shown? The drawer slide is has a 'G*' stamped into the metal. No other marking is available. The cabinets were installed in the late 1989's or early 1990's. This is the second set to break and I'd like a solution that doesn't require ... (cont.)

I have a drawer that has unigrass 6000 slider bars. Two of the drawers because of over weight have damaged plastic rollers. I'm looking for replacement rollers or complete rail. The actual rail w/roller is 21 5/8" long. Thank You, Patrick

Size appears to be 7/8 x 1/4 and appears to be pressed in. Need 4

Do you have a replacement set (2) for these. Note the rear "male fitting" that connects into the support plate in the back of the cabinet. Much thanks,

My cabinets are 30 years old and it looks like my assembly was glued on. Pus the 32-012 looks a little different - shorter than the 2.5 inches in your picture. Do you think this will work for me and will I have to glue them on?

I need to replace kitchen cabinet drawer slides for 2 large drawers that have a built in lip on the drawer sides. The existing slides mounted to the inside of the cabinet are 19 5/8" in length, but are only 1 5/16" wide at the end with the wheel.The projection of this end is 1/2", but the wheel is b ... (cont.)

Looking for part see attached photo. This is from an old cardell cabinet.

The rear adapter bracket I have broke. I cannot find a replacement in the size I need. The part number of the broken one is 6600. The size I have is one inch by a quarter inch. Everything I have found is just a little to small. The wheel on the side of my drawer will not fit into the smaller one. Th ... (cont.)

Need a new rear mounting bracket For a self closing drawer in a cabinet. The mounting bracket is slightly upright To fit the slide which is bent down into the bracket... this allows the drawer to self close ..

Do you have a replacement for this. My track is a u shape at the back it looks like.

Looking closely at parts here is the full description I could get from them; BLUM 701750 01 175H 710 02.01 cabinet latch hinge set

G*grass right 77003

I bought the bedroom furniture from Oasis Bedroom Furniture Store which has since gone out of business. As you can see from the picture the plastic brackets have broken and I need to get replacements. The rail itself is OK. Do you have these parts? If not, do you have any idea where I co ... (cont.)

Hello- This piece holds the bar to the wall for a kitchen drawer. The broken one that I need is on the right side.

Can I replace the loose roller which is causing the door to jam or do I have to replace the entire track set?

It appears to be a 1" OD by 1/4+" wide with a 1/4" hole ID that does not go all the way through, thus keeping the wheel from moving too far to the outside and providing a slide to keep the drawer aligned. I think it is made of nylon or hard plastic.

We have bought at least 2 pairs of 3/8" x 3 15/16" x 7/8" of the bottom brackets and they keep breaking. What is the problem?

I am looking for replacement handles for an antique dresser. The photo is a sample of one , it is missing the round portion on one side. The round piece is actually a separate piece the handle fits in a hole allowing it to swing.

I own 3 dressers that have the Kenlin drawer socket (32-081) & many of them are broken & need to be replaced but I can't decide if I should get the heavy duty drawer socket (32-082) vs the regular ones that came with my furniture. Your website says that both of these are interchangeable. so I assum ... (cont.)

I've ordered other things from you before and worked very well. Hope you have an exact replacement for this. Under one attachment flange is B-6. Under the other flange is 698.256 and 53.00. If not exact replacement, your best recommendation? Thanks, Jack