Viewing all customer Discussions for:

Drawer & Cabinet

I need to find additional Ronthor plastic shelving support pins. Attached are four images of the support pin from different angles next to a ruler to show its dimensions. "Ronthor" is stamped on the part and at the end of the round part is the number "92". Any help or assistance you can provide ... (cont.)

what are the dimensions on your product code 32-018 / a rear mount socket right hand for a drawer. we need a 4 3/8 long with 2 inch base - inside measures 1 inch high 1/4inch wide

I need drawer slide back sockets for a Winnebago motor home. Part number 128811-01-01A & 128811-02-01A. Can anyone advise me where to get them or an aftermarket substitute? Thanks Jack

I am hoping you can help me identify this hinge. I measured a 1/2 inch overlay and the doors open to approximately 100 degrees. It is for a pantry cabinet door that uses 3 hinges per door. There is a V inside the hinge cup. Thanks

There were two of these on the back of each dresser drawer. Almost all of them have broken off. Now the drawers don't come out straight and once they are out half way they tip down towards the floor. I'm not sure the name of the dresser. Thank you so much for your help!

I'AM NOT SURE IF PRODUCT CODE 32-025 WILL WORK FOR ME.IT LOOKS CLOSE TO OLD ONE. SUPPORTS THE REAR OF THE GUIDE. THANKS

Hi there. One of these broke off and we need a new one. It says Heritage on it, and the entire bracket measures about 4 1/2" in the "open" position as in the photo, and about 3" in the closed position. Do you have a replacement hinge? Thanks, Dave

Hello, I am looking to replace this piece for the contact of a dresser drawer. It is nailed in but has worn down unevenly and catches on the drawer when it is pulled out. This one is on the right of the frame, the one on the left is fine. Thank you for any help!

this product looks lust like mine. however, my measurements are 1-3/8" x 3/8" on a side mount slide application. My track overall measures 1" x 3/8" 22" long. Will this fit? Please advise, so I can place tje order. Thanks, James

The part is on a Lane Chest of Drawers that is stamped with # 605-18, Ser-200260. The # 115411501 also appears on a sticker on the back of the chest. It is the plastic part that helps to guide the drawer onto the center track and measures approx. 1 7/8" long, 1 1/16" wide at the front, narrowing to ... (cont.)

I need a drawer stop with the Pat 32.134. Based on discussion trails i shouldnt go by that so i am looking fora 32-076. In the dimension description it says that is 1 15/16" long. Mine is 1 9/16" long but the other dimenions seem to be dead on. Will the 32-076 work or is there a different # I should ... (cont.)

I need some nylon replacement rollers for sliding panels on my bedroom furniture bought 45 years ago from Carlton House. The broken rollers are riveted onto a metal mounting bracket, but I can use replacement rollers with a nut/bolt that would fit the quarter inch hole the rivet is in. The rolle ... (cont.)

Am looking for some the cabinet parts and hopeful that you will be able to help. See pictures. The are about 5.2'' and hole that holds the rail is about 1" long and about 3/4 wide.

Can not find these drawer slide hangers?

I AM LOOKING FOR THESE DRAWER SLIDES/GUIDES FOR A CUSTOMER. THEY MOUNT ON THE SIDE OF THE DRAWER. LENGTH-8" WIDTH-3/4" THICKNESS-3/8"

The old were so degraded and misshapen that I don't have the exact measurement; however tried the 3/4" and too big. Already drilled out the rivet (just as you answered in a previous post April 2012 recommending the 10-100). Looks like that is exactly what I need, but can't find the smaller size. ... (cont.)

We need several to make an old kitchen drawer operate in an apartment we rent

I'm looking for a drawer socket with an inside diameter of 15/16" deep. Any shorter and the drawer guide will not stay inserted. It looks just like the 32-001, only with a deeper I.D. Can you assist. Some prior questions have been placed forth regarding the same issues, and the 32-001 was provided. ... (cont.)

The plastic parts of this drawer guide have both broken (the part attached to the bottom of the drawer and the part attached to the chest of drawers. The metal part of the guide is 14". The manufacturer of the part is/was Kenlind Products Corp in Highland Park, IL. The part/patent number is not re ... (cont.)

What is this product made of? I would be using it on a boat operated on a salt water bay.