Viewing all customer Discussions for:

Drawer & Cabinet

it's cracked because it broke off. when installed (image 2) there is a sticky cover/veneer that covers the whole face, thereby hiding the screw heads as well. there are no markings or numbers on the part. i need two. approx measurements: 2" x 3/4" x 1/2" Thanks!

I have attached 3 pictures 2 pictures are of the broken part and 1 picture is of the part that is not broken. Could you please help me in identifying what this part is and the replacement part for it.

I ordered 5 Kenlin case runners (32-076) from you because I am unable to slide some of the drawers in my 16-year-old Stanley chests of drawers back into their guide tracks after I recently moved the chests. I decided the issue was the case runners, but I got the parts from you and the drawers still ... (cont.)

Total length = 20.5 inches Drawer Slide Wheel is about 9/16th of an inch diameter. This drawer slide is mounted on the outer edge of the drawer but the slide and wheel mechanism is on the inside of the drawer - not the outside. The "valley" is 7/8 inch wide and it is slightly over 1/2" de ... (cont.)

I need 3 pairs of these

I need to find additional Ronthor plastic shelving support pins. Attached are four images of the support pin from different angles next to a ruler to show its dimensions. "Ronthor" is stamped on the part and at the end of the round part is the number "92". Any help or assistance you can provide ... (cont.)

what are the dimensions on your product code 32-018 / a rear mount socket right hand for a drawer. we need a 4 3/8 long with 2 inch base - inside measures 1 inch high 1/4inch wide

I need drawer slide back sockets for a Winnebago motor home. Part number 128811-01-01A & 128811-02-01A. Can anyone advise me where to get them or an aftermarket substitute? Thanks Jack

I am hoping you can help me identify this hinge. I measured a 1/2 inch overlay and the doors open to approximately 100 degrees. It is for a pantry cabinet door that uses 3 hinges per door. There is a V inside the hinge cup. Thanks

There were two of these on the back of each dresser drawer. Almost all of them have broken off. Now the drawers don't come out straight and once they are out half way they tip down towards the floor. I'm not sure the name of the dresser. Thank you so much for your help!

I'AM NOT SURE IF PRODUCT CODE 32-025 WILL WORK FOR ME.IT LOOKS CLOSE TO OLD ONE. SUPPORTS THE REAR OF THE GUIDE. THANKS

Hi there. One of these broke off and we need a new one. It says Heritage on it, and the entire bracket measures about 4 1/2" in the "open" position as in the photo, and about 3" in the closed position. Do you have a replacement hinge? Thanks, Dave

Hello, I am looking to replace this piece for the contact of a dresser drawer. It is nailed in but has worn down unevenly and catches on the drawer when it is pulled out. This one is on the right of the frame, the one on the left is fine. Thank you for any help!

this product looks lust like mine. however, my measurements are 1-3/8" x 3/8" on a side mount slide application. My track overall measures 1" x 3/8" 22" long. Will this fit? Please advise, so I can place tje order. Thanks, James

The part is on a Lane Chest of Drawers that is stamped with # 605-18, Ser-200260. The # 115411501 also appears on a sticker on the back of the chest. It is the plastic part that helps to guide the drawer onto the center track and measures approx. 1 7/8" long, 1 1/16" wide at the front, narrowing to ... (cont.)

I need a drawer stop with the Pat 32.134. Based on discussion trails i shouldnt go by that so i am looking fora 32-076. In the dimension description it says that is 1 15/16" long. Mine is 1 9/16" long but the other dimenions seem to be dead on. Will the 32-076 work or is there a different # I should ... (cont.)

I need some nylon replacement rollers for sliding panels on my bedroom furniture bought 45 years ago from Carlton House. The broken rollers are riveted onto a metal mounting bracket, but I can use replacement rollers with a nut/bolt that would fit the quarter inch hole the rivet is in. The rolle ... (cont.)

Am looking for some the cabinet parts and hopeful that you will be able to help. See pictures. The are about 5.2'' and hole that holds the rail is about 1" long and about 3/4 wide.

Can not find these drawer slide hangers?

I AM LOOKING FOR THESE DRAWER SLIDES/GUIDES FOR A CUSTOMER. THEY MOUNT ON THE SIDE OF THE DRAWER. LENGTH-8" WIDTH-3/4" THICKNESS-3/8"