Viewing all customer Discussions for:

Drawer & Cabinet

Is there a metal version of these parts?

The drawer has bottom gliders on each side. The top glider broke. The bracket, which attaches to the back of the drawer is 2 1/2" long. It is shaped like a clamp, with the top section measuring 1/2", which is the width of the back panel of the cabinet. The wheel is elevated slightly above the cl ... (cont.)

Hi - I would like to purchase a back bracket for a kitchen drawer. The opening for the slide is, as best I can tell, 1". It is for a Yorktowne drawer. Your bracket, part number 32-119 seems similar, except for color. Do you think it will work with my drawer? Thank you.

Do u have an idea which model u have would be best. The inside opening for the guide is about 1 1/8 wide and 3/8 high and the bottom opening is about 5/8 wide at the"prongs". The whole guide is 2 3/8 wide and 1 7/8 high.

I'm attaching pictures of my problem. My hinge lock piece has broken off and now my door can't attach to the track to open and close it's a TV stand that can be closed up when not in use it has a sliding track inside. My door is 7/8 thick and the hinge that I need will wrap around the outer part ... (cont.)

I purchased some of these in the past. Does the 32-081 fit into the metal part of the 32-082? I have a couple of the 32-082 where just the plastic broke.

Your web site is laid out well and easy to use but I couldn't find the particular replacement for the tilt latch that broke in our window. It has a profile similar to 26-345 but is larger. It has an outside form and dimensions identical to pivot bar 26-379 but has the latch protruding rather than t ... (cont.)

it's cracked because it broke off. when installed (image 2) there is a sticky cover/veneer that covers the whole face, thereby hiding the screw heads as well. there are no markings or numbers on the part. i need two. approx measurements: 2" x 3/4" x 1/2" Thanks!

I have attached 3 pictures 2 pictures are of the broken part and 1 picture is of the part that is not broken. Could you please help me in identifying what this part is and the replacement part for it.

I ordered 5 Kenlin case runners (32-076) from you because I am unable to slide some of the drawers in my 16-year-old Stanley chests of drawers back into their guide tracks after I recently moved the chests. I decided the issue was the case runners, but I got the parts from you and the drawers still ... (cont.)

Total length = 20.5 inches Drawer Slide Wheel is about 9/16th of an inch diameter. This drawer slide is mounted on the outer edge of the drawer but the slide and wheel mechanism is on the inside of the drawer - not the outside. The "valley" is 7/8 inch wide and it is slightly over 1/2" de ... (cont.)

I need 3 pairs of these

I need to find additional Ronthor plastic shelving support pins. Attached are four images of the support pin from different angles next to a ruler to show its dimensions. "Ronthor" is stamped on the part and at the end of the round part is the number "92". Any help or assistance you can provide ... (cont.)

what are the dimensions on your product code 32-018 / a rear mount socket right hand for a drawer. we need a 4 3/8 long with 2 inch base - inside measures 1 inch high 1/4inch wide

I need drawer slide back sockets for a Winnebago motor home. Part number 128811-01-01A & 128811-02-01A. Can anyone advise me where to get them or an aftermarket substitute? Thanks Jack

I am hoping you can help me identify this hinge. I measured a 1/2 inch overlay and the doors open to approximately 100 degrees. It is for a pantry cabinet door that uses 3 hinges per door. There is a V inside the hinge cup. Thanks

There were two of these on the back of each dresser drawer. Almost all of them have broken off. Now the drawers don't come out straight and once they are out half way they tip down towards the floor. I'm not sure the name of the dresser. Thank you so much for your help!

I'AM NOT SURE IF PRODUCT CODE 32-025 WILL WORK FOR ME.IT LOOKS CLOSE TO OLD ONE. SUPPORTS THE REAR OF THE GUIDE. THANKS

Hi there. One of these broke off and we need a new one. It says Heritage on it, and the entire bracket measures about 4 1/2" in the "open" position as in the photo, and about 3" in the closed position. Do you have a replacement hinge? Thanks, Dave

Hello, I am looking to replace this piece for the contact of a dresser drawer. It is nailed in but has worn down unevenly and catches on the drawer when it is pulled out. This one is on the right of the frame, the one on the left is fine. Thank you for any help!