Viewing all customer Discussions for:

Drawer & Cabinet

to whom it may concern please let me know if you still cary this part thank you Johny

Looking for this part

I'm looking to replace the rollers or the complete slides on 22" slides that are labeled Jacmorr Mfg. They have the number 3451 stamped on them and also the letters DL CR. I'd prefer to replace the rollers however they are the rivet mount type. I think the slides would be considered side mount. Any ... (cont.)

my slide is 17 3/4" long by 5/8" high and has two 1/2" wheels riveted on. One of the wheels broke off. Can you get me a new slide, if not replacement wheels.

hi this is about 2 3/8" wide and 1" tall. the opening is 1-1/8" x 1/4" it has patent #3.211.510 on it. it was used on a roll top desk. it also has Ronthor n.y.c thanks

This drawer glide is from a Vaughan Bassett Dresser drawer that is about 18 years old. the only thing it says on the part is KENLIN and the number 4 sideways under it. It's 1 3/4 in wide and 1 1/2 front to back and is plastic. If I can get them I would be interested in getting a few to have as spar ... (cont.)

We are trying to replace the broken white bracket in these photos. We ordered part 32-030 because its dimensions are almost exactly the same as our broken piece. We received them yesterday. The replacement bracket (in red) has two small plastic pieces sticking out at a 90 degree and mind,peded th ... (cont.)

Greetings! I'm looking for replacement drawer guides for six drawers. I have a 20 year old wooden chest of drawers, purchased from the now closed Breuner's Furniture Store in California. I've attached photos of the parts. I was going to try to buy some replacements from Amazon, but at least one of ... (cont.)

this is the shelf bracket I need it says it is a ronthor 25-4043

the receiving slot is 1" tall and 5/16 wide. The overall length is 2.4". The mounting surface is 1" x 2 1/2" There is a logo on it that looks like a "W" but not excatly. i could not get a clear picture of the logo.

I am looking for rear drawer slide track socket that will fit 1-1/8" slide also. I have seen others asking for same. Part is Mepla 600.010.02.00 also has 2a stamped on back. Any ideas ?

6020-6 RH on the right one and LH on the Left one has a large G stamped on it with a symbol like an asterisk beside it It is 2 1/4 " deep Part where the slide goes in (outside dimension) is 1 3/8" H and 1/2" W Inside dimension is 1"H by 3/8" W the back part that screws into back i ... (cont.)

here is the picture it is 23 inches from back of cabinet to front rail

embossed in plastic: Hardware Designers Inc. #452 USA width: 2 1/2" depth: including "teeth" 1 3/4" widest distance between "teeth" (width of rail) 1 1/4" screws: 1 3/4" apart on center drawer back thickness: 7/16" to 1/2" (screws?) I would like to order 10 glides + screws. Thank you Sharo ... (cont.)

If the axle is removed what is the diameter of the remaining hole?

We are home owners wanting to replace four (4) kitchen drawer guides like the one pictured below. The measurements are: 1 & 3/4" by 1 & 1/2" Our home was built in the 1980's. If you cannot replace this part do you know of any place that can do so? Thank you in advance for any information ... (cont.)

Looking everywhere for this part.

Looking for plastic wheel 1-1/16 Inch diameter and 3/16 inch wide. It's from a 1950s steel kitchen cabinets .

I would purchase 2 of these hinges, if there is availability.

this a grass undermount slide locking device from american woodmark cabinet similiar to your 32-336 but not the same as please help thank you