Viewing all customer Discussions for:

Drawer & Cabinet

TWIMC, The little wheels/rollers came off the side of a dresser drawer. The drawer itself has heavy duty metal sides (6" x 14-1/2") and the drawer front, back and bottom are wood/MDF. There are plastic brackets attached to both sides at the top back, where the metal sides meet the wood back. Thes ... (cont.)

I have a bathroom vanity with a drawer assembly that has a pair of 1/2" (Outside diameter) wheels that fit into a metal track. The wheels (one on each side of the bottom of the drawer -- in the very back) are attached to back of the drawer with two staples. I would very much like to locate a pair of ... (cont.)

I need a few replacement nylon rollers for my drawer slides. The rollers I need are 7/8 inch, with 1/2 inch holes. The first picture is of the drawer slide without the wheel. The second picture is of a complete drawer slide. The third picture is of the broken wheel. I would appreciate any hel ... (cont.)

Good Morning - I am looking to buy replacement brackets for my kitchen drawers. The drawers themselves are plastic and rest on the current brackets seen in the attached imagaes. Thanks for your help. Chris

Looking for one of these to replace this broken one and the hardware to secure it. I do not know the exact name, model or piece number, please help. Thanks. Shawn

I am looking for a flat furniture drawer stop that attaches to the inside bottom rail of the drawer opening, not the drawer itself. It is a flat white plastic piece that measures 5/8" x 2 1/4" with a sloped raised edge that prevents the drawer from following out. Do you have any idea where I can fin ... (cont.)

Is 81-018 a possible replacement for MI (Metal Industries?)sliders? This model seems to be the closest to what I have pulled out from door in regards to measurements. Thanks, Eric

This drawing is of the mounting hardware for a rolling cabenet door. On the harfware it says, LEIGH

Sirs, The picture I've submitted is a picture of the part I am looking for. I found a similar part on your website that matches the dimentions given but, there were only two dimentions given, diameter of insert into hole and width from inside of guide to outside of guide. Both of these match my p ... (cont.)

I am looking to purchase 2 sets of draw stops. They are 3/16 thick and approximately the size of a quarter in diameter (15/16). Please let me know if you carry this item. Thanks, Deborah

are your 32-014 drawer slide sockets made left hand and right hand or are they considered symmetrical thereby useable on either side of the drawer?

Your best bet is to match the dimensions of your guide to the dimensions found in the product picture. We have our 32-031 listed as the replacement for the Ronthor 2857233, but it is a larger guide than the 32-030. Sometimes patents are for the whole drawer system and not the individual pieces of th ... (cont.)

I need replacements for some broken drawer glides on an Ashley furniture dresser. The measurement of the glide is 1/2"L x 5/8"W x 1/16"D. I have attached photos. Thanks

Looking for a replacement for the attached door handle from a Yound Hinkle cabinet. Numbers on the back say KBC N8129 or N8139. The one number is hard to distinquish. Will need all hardware parts for this handle/closer. it's about 5 1/2" long and 2 1/2" wide. Thanks so much.

Please advise if you have sockets that can be used to replace attached sketches.

I need to replace 6 hinges. I need these identified so I can order correct hinges. Thank you, Richard

As you can see both my brackets for my drawer have broken. they brackets on the left illustrates how the bracket is broken. and the one on the right shows how it must look when in original condition. But both of the brackets are broken for the under drawer mount. please contact me to resolve this pr ... (cont.)

I need 8 pair of these drawer sockets. Dimensions are as follows: Mounting plate 2"H x 1 5/16"W, socket depth is 3"D. Glide socket I.M. is 7/8"H x 7/16"W. It comes from a cabinet by Sears and is about 10 to 12 years old. A number stamped on the back (102). I'll send photos. Thanks, Mike ... (cont.)

Hello, The house we bought has center-mount drawer slides with a central metal channel attached to the cabinet, rollers on both sides of the cabinet opening that the drawer sides roll on, and a white plastic glide screwed to the back of the drawer. Most of them work just fine, but a few of the pla ... (cont.)

Hi! I'm looking to replace drawer sockets that have broken. They are similar in design to your mode 32-014, except instead of 7/8" slide opening, mine are 1 3/4" to hold heavy duty slides. Do you have anything like this or know where I can find them? Thanks!