Viewing all customer Discussions for:

Drawer & Cabinet

I need 2 pair of these drawer guides

I have included pics, with measurements etc on on the attached document. The stamps on the socket are G 6600. There is a C stamped on the corner. There is an L stamped on it, I assume that is for left as it came off the left side.

Hi. Totally not using technical terms here, but I need four of these bad boys for a 1970's modular home were remodeling. Two drawers cannot be reinstalled because we're missing two of these. My hubby would rather nail the drawer fronts on and call it a day. I have faith we can keep these drawers ... (cont.)

I need to replace some of your rear glides that are quite old. The number on them is R-26 and patent number 2857233. Can you please identify the correct item. photo attached

from the square end to the large round end is less the one inch the rectanle that both the large round end and small pin like post is 3/4 of an inch. Sorry the last picture is very out of focus. Thanks for your help Roy

I am considering using this track to replace wooden tracks in my daughter's vintage furniture. It says 22" and her tracks are 16". Can they be modified, if so, how do you recommend doing so? Thank you, Terry

I just received my order. It was earlier than expected! So happy I found your site on line. My furniture dealer couldn't send me replacement parts and my local hardware store didn't have what I needed. These sockets and runners were perfect! I will definitely order from you again and I will tel ... (cont.)

What type of stopper would work with this drawer from an inexpensive roll top desk? I can not tell how 32-125 drawer stopper works.

I have inherited a set of metal laboratory-grade cabinets, enough to equip my entire workshop and for a great price (free). The only thing wrong with this set is a bit of wear and tear, including worn out / broken nylon rollers on the drawer slides. the drawer slides are welded onto the meta ... (cont.)

we have a white plastic drawer guide that needs replacing. The dresser is about 10 year old. The part reads "Ronthor Reiss Corp N.Y.C R-40-28 Pat# NO 3,201,187 the part is 2 3/8 inch long. I have attached a picture I would like to know how I could order 4-5 spares

My rear socket has the letters FGV on it. It looks similar to the 32-119, but the bottom of the slot slopes downward as it it goes towards the back. Specifically, the top of the slot is horizontal, while the bottom of the slot is horizontal for about an inch, and then it slopes downward as it goes ... (cont.)

I have german (brand = Lager) kitchen cabinets about 25 years old with deteriorated drawer slide rollers. I would like to either replace some of the rollers or the complete slides (see attached jpeg image). The rollers are 3/4 inch in diameter and 3/32 inch wide with a rivet hole about 3/32 inch. If ... (cont.)

Hello Paul, I have NOBILIA vintage kitchen suit from 1972 where some drawer guides have broken. The Guide is signed RONTHOR N.Y.C. Patent 2857233. This is the piece in the bottom center of the drawer that fits over the strip of wood. Can you help me with replacement three pieces? I also sen ... (cont.)

I need a replacement of a Ferarri G023 Slide Socket. Photo attached. Do you have this or something that will fit? Thank you. Cindi

I have a set of kids' BARN DOOR bedroom furniture. The back socket on all the dresser drawers have broken or cracked and the "slides" that go in them hang up or down, so now all the drawers do not close properly. Is there a replacement piece for this back socket "plate"?

Do you sell Tippers? I need the white one that is located on the rear of the drawer (see attached photo)

Hello, pleased to find your site. I'm looking for a replacement rear drawer guide (same as the one pictured) for a drawer in a wood filing cabinet. I believe you carry what I need, but I want to make sure I get the right size. The opening on the plastic piece for the track is about 1-1/8" x ... (cont.)

I need something similar, but a much more heavy duty to your #32-083 Corner Tack Glide. Your #32-305 Shelf Support may be a candidate, but I'd need to drill a 1/4" hole for the peg and another screw hole to steady the whole affair. The pictures are attached. I don't have any markings that I ca ... (cont.)