Viewing all customer Discussions for:

Lavatory

I'm looking for a shower sweep. The shower door has no frame. The sweep measures 24" total but 22" attaches to the door.

not sure if this is user error or maybe I need another product I installed the below product and am not getting a good seal. I matched what the previous home owners installed on their door....i thought i leaked because it was badly worn. upon closer inspection, the door swings OUT and pulls the w ... (cont.)

I have a framed shower door that has a plastic sweep that needs to be replaced. I'm having trouble finding the correct part. It appears to just slip on the glass (1/4 inch thick) and has a drip rail on the inside to direct water away from the base of the door. The sweeps I have seen appear to be for ... (cont.)

Please find attached the picture regarding the part for the shower. Thank you. Kind regards, Aleisa

How many fastener holes are on this drip rail? Would like to know how many 33-071 screws to buy but this information is not stated in the description of the drip rail.

How much floor clearance do need?

Unitex ANSI Z971-2004 SGCC-25763/84 The bottom slider to my shower door cracked and I need to replace how do I get a new one. Please advise Patty Thank you

I ordered a 3/8" shower sweep but unfortunately my shower glass is 3/16 not 3/8 as originally thought. Can I return these and what size should I have ordered as I do not see one for 3/16 inch glass?

My shower door has apparently never had a door sweep installed on it. I recall a plastic strip being there, but that came off years ago and I don't know how it was mounted. I don't see how a sweep would be installed since there are no holes for screws. The frame appears to be chrome or plastic. Not ... (cont.)

DO you have instructions on height positioning? i.e., how high, how low relative to the door frame the sweep has to go over or clear. (The previous install in my home was done where the sweep was folded under when the door was closed, so that it allowed water to go to the outside). How high is it po ... (cont.)

I need to get a new sweep for my frameless shower door. Not sure if I should get the one with the drip guard or without. I think my current one has a drip guard, but the photo of your product seems to show the drip guard In a different place so want to make sure my door will close properly. ... (cont.)

What part do you recommend to replace bottom of shower door Glass is 3/8 and length is 29 1/4

I just had a frameless glass shower door installed. My problem is that when the door swings out it can hit the toilet bowl and shatter. Is there a stop or guard that will keep the door from opening to that distance ?

My shower bottem guide is about 2 inches long and half in. tall. This shower was bought at Home Depot maybe 10 years ago and they don't make or store the part at their stores. The guide is about one fourth wide. Please let me know if the picture you show for the 10-127 is the same one that I need ... (cont.)

Roller for a shower on a 2010 tiffin zephyr

I need the rubber strip that goes at the bottom of the shower door.

Where can I get a replacement of this type of aluminium sweeep? 21.5" long, 1st hole- 4" from edge, then another 19" and has another hole (or 2.5"form another edge). The bottom L is about 5/8", about 6/8" slight bend.

I want to replace Dear Swisco, I want to replace seals/sweep on 20 plus year old shower door and feel I have properly identified the sweep (10-336/5) and vertical seal (10-328/9). However, there is a channel on the opening side of the door as well as across the bottom that also conatin seals (p ... (cont.)

Hello. I need to replace mine and the door is 24 inches wide. What do you suggest to use to remove the old one, cut the new one and adhere the new one? Anything else I might need to order to do the job? Thanks.

Do you have a 10-327 type sweep that's longer than 3/4"? I need the sweep to be 1. ".