Viewing all customer Discussions for:

Lavatory

I need the plastic seal that goes on the bottom of our shower door. Here is a picture of it attached. The length is 21.5 inches long and not sure the width of the T? Maybe you can help. Thanks. Lenny

I may be able to use this seal. You show tearfoo strips to adjust height. I need approximately 5/8" rang. Can I get it. thanks Paul

regarding the pulls mentioned above 10-005, they look perfect for my medicine cabinet, but can you tell me how thick they are, because this is a custom made cabinet and there is very little space between the sliding mirrors? Thank you

Looking for shower door sweep, t-style 1 5/8" x 1/4".

Many more pix with email I hope you can help me because I don't want to replace a shower just because I am missing a couple of pieces of hardware. My shower came equipped with 2 double rollers at the top of each sliding door, but, because it has been installed for six years and is now discontinu ... (cont.)

Guide hook for a sliding shower door

I am looking for replacement bottom tub shower door glides. I was told that my original glide is a Pasco unit. Do you have them. Your 10-139 guide physically looks close and the dimensions are right, except mine is 1 1/5/8" in height. Not a big deal I guess since the difference can be adjusted v ... (cont.)

Hi there, I've trying to find this piece so we can change the existing one. The sliding door are hard to open and it seems that this part is damaged. Can you help me with the part number and if you have it or not. Thank you Naz

How does a person remove a concealed twist type latch that is loose to repair or replace? It is very loose and will not lock the door but I can't get the latch apart or see how to remove it. Thanks for the help, Ken

I want to install the following door handle to our shower door #10-129. I see your measurement for thickness of door is 5/8", our door is only 3/8" thick. Would these handles work? chet

RE: Door Handle With Towel Bar Insert, 2-1/4" Product Code: 10-133 got a set....they fit the shower door holes, the towel bar slides in fine....but now the bar seems a tad short.... any suggestions what I could stuff in the door handle openings to reduce the sliding back and forth...it would ... (cont.)

Hi - I have previously purchased several of your shower door sweeps - part 10-310 - but I don't see it listed as available any longer. Am i missing something? Alternatively, is there a comparable part that you recommend? Thanks

How do you remove old hook guide?

I purchased a home that has a Keystone shower door assembly with missing bottom hook glides AND spacers. It appears that the Swisco 10-139 will work and I am prepared to order a pair. Where can I purchase the spacers?

I need to have these replaced. Does N.K.G. mean anything?

I have been looking fruitlessly for some time for replacement wheels for my shower doors. They are 3/4" O.D. with ball-bearing race and brass hollow bored axle for a self-tapping screw. The wheel itself, however, is only 3/16" width, with a flat profile, and that's the problem, as any potential sup ... (cont.)

Replacing broken handles on a two sliding panel shower. Original handles had a towel bar, which is now out of style. So replacing with simple handles. The 10-126 looks to work to replace on the outer side frames. (My door appears to be 1/2" width, so hope that is not an issue) Any product t ... (cont.)

Do you have a 10-126 on 3 5/8 centers instead of 2 inch?

Do you folks offer these handles in 2". I found product #10-138 but those are 2 1/16 on center. Also do they come with the mating handle for the other side.

I have an old sliding shower door with the double towel bar brackets which I can't parts for. one bracket is missing and one bar...as i can not find the double handle brackets anywhere i thought I'd go with your 2 1/4" single brackets....but how do I get the OLD double bracket off ?? Is ... (cont.)