Viewing all customer Discussions for:

Lavatory

I was referred to you by Frank's Building Supply in Franklin Township (Somerset) NJ. I am looking for a part that fits into a shower door handle/towel rack on each end. It is a "male" insert, there is one on each end of the rack and is then attached to the door by 2 screws. It is basically U SHAP ... (cont.)

I have a picture HELP IN TROUBLE I need some HELP FAST with these wheels

I need a pair of Allen-Stevens shower door top roller hardware, part number: A-S 3957 Can you help me?? I hope so !! Thank you !! Bill

Rollers are on every other panel and a plastic peice that is on every other panel. They screw in a panel like the rollers do. What are they called, the price and can they be ordered. I need rollers and those little plastic peices. Do screws come with rollers and the plastic peices? I have a tub-ma ... (cont.)

I purchased a corner round shower door kit a couple of years ago and installed it for a customer. The hardware recently broke and I'd like to find the replacement part. However, I cannot find the manufacturer's name on the kit. I've attached pictures of the part I'm looking for. I'd like to ... (cont.)

I am a volunteer at my church and I am trying to get our dilapidated restrooms back in shape. One bathroom has a single stall with no hardware to close and latch the door. I have searched on-line and have been able to locate a few latches that could work, but have been unable to find a strike and ... (cont.)

I am looking for similar glides for shower door. Maker of the door is Alumex and it is approx 20 yrs old. Attached is a picture of part. Your part# 10-139 looks very similar and the dimensions are the same. Can you look at the attached picture.

Hi Folks- Trying to fix this restroom partition lock, and also need to add some sort of keeper component, to keep the door from swinging outward (only need it to swing inward). Also, what options do I have to put a privacy panel up on the outter part of the door- where the toilet is located, your b ... (cont.)

how long is the lock bolt? It only says that it is 3/8" in width!

Hi there, I need to find a replacement to a roller for my sliding bathroom door! I can't seem to find one that looks exactly like it in your catalog and anywhere else. But I'm sure you must have one that should fit or identical to it? It is an Allen-Stevens corp. part # A-S 3637 Please see attac ... (cont.)

I was looking at Product Code: 10-134 which is a roller assembly for a shower door. Your wheel measurement is listed as 1 inch. All of the other measurements are the same as the replacement part I need: except, my wheel is just a little bit smaller than 1 inch. I was wondering if your wheel measures ... (cont.)

I am going to purchase this item to replace a snap on sweep that is not tall enough to fill the gap between the bottom of my frameless shower door and the curb (manufacturer set included a 3/8inch sweep but the door and hinges are drilled for a 1" gap?). Anyhow, I'm wondering if you would recomm ... (cont.)

Is it possible to purchase just the rubber tips for the coat hook 10-525? Looking for 100 or more.

Does this knob assembly come with locking washers to hold the two pieces in place?

I am trying to replace the knob assembly your part # 10-556 on a bathroom door. Do you have some directions on how to install the replacement knob. Looking at the part it appears that the knob presses into the door, but I am not exactly sure how to go about this process.

I have Stanley Mirrored Sliding Closet Doors. I need handles for 2 of them. My other Stanley doors have a handle that looks like your #:10-005 clear flat adhesive handle, but they are glass. Is this item glass?

What is the thickness of door that a "10-557" will fit? My doors are about and inch thick

I need to replace my bottom rollers on my sliding bathroom mirror. The chanel on the mirror will only accept a roller that is 7/16" wide. Do you carry them in that size?

We need to replace rollers on 5 slider windows that measure 3 x 5-1/2 ft. high. Do you recommend the Heavy Duty roller (10-118) or the 87-006A (which is what we appear to have now)? Also, any installation hints would be appreciated. The windows enclose a 2 story sunspace so access to the gl ... (cont.)