Viewing all customer Discussions for:

Other

Length is 32" & 5/8. The only stamp is 32DS 45 and in smaller letters after 45 is RN then either 1S8 or IS8 then TJ. It is a Milgard viinyl single hung window, we believe it is part of the Tuscany series (8220/8230/8270) made in 2008. We will need 2 balances.

Hi my name is James. I'm gonna need a set for each window of top and bottom pieces pieces if you can locate these. And I'm also looking to have a screen made for this screen door I don't know if that's something you could do and ship or if someone in the Springfield Massachusetts area would be abl ... (cont.)

Looking to replace the broken latch on a Simonton sliding window. The PAT# is 5,553,903. Please see attached photos.

Hello there, I'm looking to replace hinges on a Thomasville entertainment center and inquiring if you have anything like this that I can purchase. Hinges are partial wrapped non mortise type as shiwn in the attached picture If matching hardware are not available can you please recommend a good repl ... (cont.)

The roller is 1 1/4" and the rear width under the screw is roughly 13/16" maybe 7/8". The total length from front to back is 2 1/4" long. I need two of them as the door is really heavy and it won't roll anymore. Thanks for your help with this Dave

Need bottom track for Bifold mirrored doors. Track is 1 inch wide, and roughly 5/8 inch tall and opening 1/2 inch

I need 30 sash guides to go with my recent purchase Of S380-30 guides.Please identify the part I need from the pictures attached thank you very much

I need to replace both of my up/down window channel balance. I do not know the manufacturer of the window but it's about 20 years old. Also, the windows did not have the take out clips; Is that normal to not have them or perhaps the installer to remove them? Thanks.

I have a broken cast hinge Mepla 698254 for which I need a replacement. can you help?

The metal portion is 33" long. I have included pictures of the end pieces, and a mystery piece that fell out when I removed the window. It appears broken. ThanksGreg

Inside lever will not spring back. ESO 0106910

The part is 3" long, 1" wide and 1/4" thick. The two screw holes are 2 5/8" from one hole center to the other hole center

Hello I need help identifying parts that cover lock and open/close handle parts. Also need screen for this Anderson window. Second window need only casing for part with handle and for lock on right side, I don't know which brand this window is. Thank you

Length is 36"

I'm looking for the complete handle hardware replacement. I'm also looking for information on how to remove the remaining parts for new installation. It's a Legance 3 door Type : DDSG Code : TRI - K - 36 Any help is appreciated! Kevin

Hello,I am in need of replacement door handle for my screen door. Would you carry any part to match the pictures above?Thank you.Luci

Can you please help me identify replacement parts. I have four Anderson window that need replacement sash balances. These are the numbers that I found on sash balances and the approximate glass window areas: Living Room - 11600-3 E25 9#27 5-85 (2 balance components), Glass area 36 7/16 X 23 5/16" ... (cont.)

Could you identify a replacement crank from this old style. The overall hight is 6" The body is 4-1/2 " Tall 2-1/2 " deep The Bottom screw bracket is 2-1/8 wide Crank handle is 4" AOL

Hi, just bought this place and found the sliding door misadjusted and I am unable to readjust the rollers. Found the friction lock device to adjust the door height is bad on both door rollers with the internal nut stripped on one roller and the adjusting screw is marred beyond use on the other roll ... (cont.)

Hello,Happy Black Friday.I would like to order 4 replacement sash springs for this Ply Gem Silverline. I would also like to order 4 of the tilt shoes.Thank you so much,Bill 11/26/21