Viewing all customer Discussions for:

Other

Hi there, I'm looking for replacement weatherstripping that would fit our De George (Buffalo, NY) windows. I've included a picture of the profile of the seal, pulled out a bit, and I've also included a sketch with approximate metric measurements. Please let me know if you have any pointers toward w ... (cont.)

hello, I am looking for a replacement for hinges used on Haas kitchen cabinets manufactured in 1995 or 1996. The visible stamp on the door side is Amerock. On the reverse is 2110 and a 2 inside a circle. door side mounting screws are 1-7/8" on center. Bore is 35mm. Frame side of hinge is stamped B, ... (cont.)

Hi, I think I'm dealing with a right hand opening casement window. Truth entrygard would like a quote for the operator and some underneath parts (not sure what they are called. I think it's a Link Arm.The operator has this stamped : 1982 , truth entrygard , on the main plate near the gears is 10471. ... (cont.)

Hi, I am so excited to find your site! I am trying to repair some windows for my mom. They are Silver Line 2900 series tilt windows. The locking shoe is broken on several bedroom windows. I don't know much about this, so hoping you can help. One of the attached photos shows the broken shoe. Stamped ... (cont.)

Slider for Horizontal Venetian Blinds between Glass Panels of Patio Door (Anderson?)

INTEX TEMPERED ANSI Z97.1-2009 16 CFR 1201 II SGCC-2573 5/32 UA

Hi! Looking for rubber piece insert to slide onto two lips on both sides of the bottom edge of door. Thank you!

Hello! Do you carry this part? If so, do I buy individually or is there a pack and is so, how many in a pack and price. Sorry I do not have photo of part removed.

5/8", 17". White tip. Cannot find any on your site that have that attachment at the end. Cannot find any anywhere to be honest. That part was attached to my window. At least I think it was. Windows were probably done in the late 60s early 70s.

I am looking for replacement weatherstripping for my wooden double hung MW windows. The bottom seal appears to be kerf style weatherstripping (~1/4" kerf insert), the sash to sash seal and top seal appear to be a kerf style bulb type. I am also in need of the plastic insert that goes into the window ... (cont.)

Theere was no marking of any kind on the part.

I am looking to replace this channel balancer. The part number stamped on it is q-28-1. It is 29" long (channel only) excluding the top and bottom accessories. Any help you can provide would be appreciated.

Hi Have a couple broke balances and a few window sash guides broke. Metal balance is 30"x 1/2" with winged top and bottom nylon pieces Any help would be appreciated Brad

The window does not fully close at the bottom part of the window. the repair person says he can't find these parts anymore. He says he needs Sash, Hardware for hinge arm, sash pívot, rotor gear. The numbers on the parts are: EntryGard Truth Hardware 20755 40887 40941-A

Window information: Hll-280-1 NFRC Series: CLCASE WindowThere are two different clips, I need the one in the picture.

Greetings, I have 8 aluminum windows (unknown brand) in which the screens are not tight allowing insects get in at the gaps. It appears the problem is the plastic clips have broken (making for 1 then there should be 2) and/or have been weak over the years not keeping the screen tight. If such a gadg ... (cont.)

Pl let me know if item is available. Thanks

The metal channel is approximately 22 1/4" long and 1/2" wide. It has stamped on it 22 4. I am unable to find the manufacturer for the windows. So, I have been unable to contact the manufacturer. So your assistance is very much appreciated. If you need more information, please let me know what ... (cont.)

need help to identify what to purchase, original pic from when home was being built showing window manufacture.

16" channel it has the number 1540 on the side.