Viewing all customer Discussions for:

Other

looking for sash lift, bar, as on windows put in in 1986 the lift, #OF374000 might do but I cannot get specs on it.

Not sure how to order these parts or what I'm looking at

bracket that holds the stationary door in place. suppose to be one at the top and bottom, my door only has one at the bottom.

Photos attached of screen door rollers. No names or model numbers available. Te mechanism uses a gear and drive for adjustment of roller wheel. Able to identify or provide part?

Your Legacy lock set looks identical to a lock set I have on a Vetter (brand) French Slider installed in '05. Vetter is no longer in business I believe and purchased the lock sets from someone else. do you have install spec's on Product Code: 82-086? I'm looking for tech spec's to compare with wh ... (cont.)

1 inch white

I need qty. 6 MW parts shown in the attached pictures. I know MW has gone out of business so I need your expert advice. I need the eite crank mechanism and associated parts for complte replacement. Thank you !!!

Hello, I am trying to find the right replacement for my screen door and am hoping you can help. The measurement is in the photos. Thank you!

HelloNo manufacturer marks on screens, installed same time as Jeld-Wen windows either 1986 or 2006 (most windows were replaced in 2006, unsure if they replaced the screens as well). Any assistance in obtaining replacement corners would be great!ThanksPat

Dear Sir/Madam: 1. I have a couple Am. Craftsman Home Depot windows, 10 years old. The coil balances are bad on both sides of the bottom window panes. These panes weight about 10lbs. The windows panes are 21" x 28 3/8ths". Frames roughly 24" x 57". Outside width of the side channels is 1.5". ... (cont.)

I have about 10 windows that will not stay up. I believe I need to replace the block & tackle mechanism?????? Been watching your videos. Letters/numbers Unique 27-0-40 Any other information I would need to have when I order?

I'm looking for the hardware handle and lock for this Windsor patio door thank you Jon.Very important. Door itself has the lock in it but we don't have the plate striker the striker plate or the handle or the lock as you can see in the photographs it was made 2014 in Des Moines Iowa. I have contacte ... (cont.)

photos are attached, let me know if you need anything else thank you

The window crank is bent and releases the pin/barrel that holds the crank wheel. The label on the window says CODE: HII NFRC CLCASE 2650 HII-1-006-7/14-15 97-M Could you please confirm which replacement handle I need? Thank you, Susan

Sash lock has a symbol that resembles a letter B

bugs can come in the house threw the sides of my screens , I need clips to push the screens in nice and tight , these are the clips on the screens now , please help

Hello, I'm looking for a window latch that is similar to the picture shown below. Unfortunately I can't find any manufacture insignia on these windows. Do you know what type of window manufacturer uses these and/or do you carry a replacement part? IMG_6171.jpeg thank you in advance, Michael ... (cont.)

Hi, I am trying to find the correct model for this window sash tilt latch. I believe it to be the silver line product line 1000 series but I'm not sure of the model number to order a replacement for it. Any help identifying it will be great. Thanks!

Hi. I am looking for replacement balance coils for our Anlin bathroom window. It seems that this is a 2 part setup and your company seems to come the closest with Part No. S140, but it is not a dual piece setup. I have included photos of the back of the coils that show a marking of '8R'. Thank ... (cont.)

The windows and doors in our house were installed in 1996. They all seem to be the same brand, but there's no identification on them. Or at least none I can find. Some of it has broken away and all of it is old and brittle so I would like to replace it. I only uploaded the door pictures, but I ha ... (cont.)