Viewing all customer Discussions for:

Other

I am looking for a storm glass door retainer. This is about 74 inches long, color white.

I want to replace this current setup with a keyed handle set. I was looking at 82-086. Will this fit my configuration??The dimension for the mounting holes are 3 15/16.Please advise.Al

Do you carry sashes? What I have was installed in the mid-80's. They are Norco casement winidows. One of the windows is showing some exterior wood rot as moisture probably got by the weatherstripping which is a bit loose. The perimeter of the aluminum cladding is 64.25" x 23". The cladding is b ... (cont.)

I have a patio door from this company and I need a replacement handle. The handle is from their Legance II product line. The interior base measures 6.750" tip to tip and the mounting hols are 4-15/16" center to center. The door is 1.50" thick with a duel point lock as shown in Handle-1 pic. I ne ... (cont.)

Im looking for 14 of these parts

Do you have a part that would replace a milguard balancer with a 25 5 stamp?

Greetings. We have a slider window on which (from use) the small piece on edge covering the weather stripping cracked and has separated half way down the height of window. This piece no doubt helps keep air tightness. But is also seems to be integrated into the channel that creates edge and wraps to ... (cont.)

We are in need of a replacement sash for a 2000 OC sliding window. Thw following is all the info off the old window that we have.F0196 2CWP 6-19-0004275914010001sach left 25x45.375 1-1/4 thickWH2 H517 LFSLW23Do you have this sash available ? If so what is our cost?Thanks - Steve

Looking for a replacement door handle. I have a Champion Patio Door installed by the previous owner of our house. I do not see any part #'s on this part. Are you able to help me out? Let me know what other info you need, I can try and get it.

I am looking for patio screen door lock as shown.

good morning. Got your name from pella. Looking for the locking lever for the door in pictures above. It is dated 1975. At the very least, I would like to purchase lever only.

I know the mounting holes are 4" apart (center to center) and the color seems to be a light beige. I can not find any names or part number on the door or door handle. Can you help me get the right handle?

Looking for the window hand crank assembly. 7501 series American craftsman.Thanks,Sue

This is a replacement window approximately 15 years old. They are double hung and this gasket is the lower gasket on the bottom window. I would like to buy at least 20 feet of it. Thank youBrian

Need plastic part of slider

I need the crank mechanism for this ownes Corning windown ally the way to the outside including the handle

Hi Swisco, I was looking for your help in ordering the above pictured part for my Arcardia Sliding Screen Doors. The part looks very similar to your 084-074N but my piece does not have the center tube for tension screw, mine only has a screw hole. Is this tube piece attached/ fixed to the roller ... (cont.)

Between each drawer there is a shelf which protects the contents of the drawers from falling into the drawer below...what is the term used to identify these shelf like deviders???

Hi, I like to replace my window balance: 32 5 GS CALDWELL (shown in one of the photos). Please let me know which part number can I order and how much it cost for a pair? Thanks, Tom

Measurements it's 4 & 3/4th inches tall, the rail slot is 1 inch high and 1/2 an inch side. Depth wise for hanging is 5/16ths deep. I ended up ordering HANGING RAIL BRACKET, 1-7/16" DEEP Product Code: 32-025, in hopes it'll work but I figured I should ask here in case there is something better. ... (cont.)