Viewing all customer Discussions for:

Other

need replacement handles

Hi Swisco, please see attached pics of the Loewen balance - the item is for a tilt-out window and is stamped with 25D ... 25 in length and 1/2 in width. It installs recessed into the channel with two cam pivots on the sash that mount into the clamp on the end of the string. Mike

id part window No#mc/c-m XI

Hello, I need assistance identifying the correct replacement counter balance. I will nee 10 of them after I have successfully identified them. Please let me know if you need further info. On the side of one of the counter balances is says "30 3 cn caldwell" Thanks, Joel

Hello...we had two double-hung gorell windows (Side by side) installed around 14 years ago in our family room. We didn't get to choose our windows, the contractor did. I now need to replace the screens. Any chance you can help?

Looking for a coil balance on a MI Series-350 SH window that has a tilt latch.

I am looking for a replacement sash balance for my Andersen Window. I attached the pictures of both the balance and window. The Balance has three multiple numbers on it: On one side, it 11600-17 and 931 R78 2\02, on the other side it has 11600-A-3. The window is a 4x2 (both lower and upper panel ... (cont.)

I am looking for a replacement sash balance for my Andersen Window. I attached the pictures of both the balance and window. The Balance has three multiple numbers on it: On one side, it 116---17 and L1/127 P97 401, on the other side it has 11600-A-3. The window is a 3x3 (lower panel 39.5''x32') a ... (cont.)

Lock no longer works No part number On lock Only two patent numbers 6,264,252 5,820,170 And DEC 07

Hello, I'm unable to identify the correct replacements for these sash balances. The window is a double hung window measuring 24" W x 36" high. Please advise. Multiple pictures should be attached. Thank you.

The first three pictures are 25" x 1/2 (2440) , the last two are 17" x 1/2" (1630). Before purchasing I saw several that looked alike and I want to make sure its the right ones before purchasing .

I believe I would need a 15046 pivot shoe, but the picture I've unloaded does not have the notch in shoe where the window pin fits into the shoe. Is this pivot shoe compatible with Crystal Window products? The window is either a series 100 or 200, but I believe the hardware for both of these serie ... (cont.)

I am looking for a storm glass door retainer. This is about 74 inches long, color white.

I want to replace this current setup with a keyed handle set. I was looking at 82-086. Will this fit my configuration??The dimension for the mounting holes are 3 15/16.Please advise.Al

Do you carry sashes? What I have was installed in the mid-80's. They are Norco casement winidows. One of the windows is showing some exterior wood rot as moisture probably got by the weatherstripping which is a bit loose. The perimeter of the aluminum cladding is 64.25" x 23". The cladding is b ... (cont.)

I have a patio door from this company and I need a replacement handle. The handle is from their Legance II product line. The interior base measures 6.750" tip to tip and the mounting hols are 4-15/16" center to center. The door is 1.50" thick with a duel point lock as shown in Handle-1 pic. I ne ... (cont.)

Im looking for 14 of these parts

Do you have a part that would replace a milguard balancer with a 25 5 stamp?

Greetings. We have a slider window on which (from use) the small piece on edge covering the weather stripping cracked and has separated half way down the height of window. This piece no doubt helps keep air tightness. But is also seems to be integrated into the channel that creates edge and wraps to ... (cont.)

We are in need of a replacement sash for a 2000 OC sliding window. Thw following is all the info off the old window that we have.F0196 2CWP 6-19-0004275914010001sach left 25x45.375 1-1/4 thickWH2 H517 LFSLW23Do you have this sash available ? If so what is our cost?Thanks - Steve