Viewing all customer Discussions for:

Other

Thank u I received a package of weather strip Item# 57-055 9/32"bubble seal with angled base 75' Do I need tools to install the strip? Proper to insert?Joanne

I have a sliding door with a part of the manufacturer's original sticker on it that says: Code : 15-1 Spec: SGD-B1-HP(40) Before I disassemble any of the doors I was wondering if you know the type of roller/assembly that is used on this door, given that limited information. thanks. ... (cont.)

WE have Mepla hinges on our kitchen cabinets and a couple of them no longer keep the doors closed. So need to replace them, They say made in Germany. The number on the hinge is 674 229 70 00. There is also separate numbers of 92 and 29. Where can we get the replcement hinges?

I need to replace two sets of balances for Andersen windows installed in 1987. The window measures approx. 55 x 36. Any chance you can provide the type of balance I would need to order just from the date of installation and size? I'd like to avoid having to disassemble in order to get to the balan ... (cont.)

Doors and windows are Weather Shield. Need weatherstripping for 8' French doors. Need crank out for windows also need bottom guide for window pane as well as the bottom track. Need bottom weatherstripping for French doors.

I have a window which needs to have the counterbalances replaced. It's a Milgard. The sash tilt's in for screen replacement and cleaning. The length of the square aluminum tubing is 21". The sash weighs 20 lbs. There's a number stamped into the Aluminum: 2040. Does this tell you enough to ID ... (cont.)

A friend has casement windows identified only as 'Roti' with a curiously shaped R. The weather seals have become gummy and crumbly with age. Can Swisco offer a replacement seal? The fin which sets in the kerf measures 1/4" deep, the attached side 3/8" wide and the other side of the 90° angle 5/16". ... (cont.)

14 inches long

Complete door, just the sliding door, not the frame. 96" door

These are parts for Devac High Performance Aluminum Windows Probably date to 1960 to 1970's Most in need of "pin" with one hold The pin measures 1 7/8 inch The hole is about 1 5/8 from the left (long end) of the pin

We are looking for window balancers. part on existing balancers are 19-5, need 2 and 25-9 need 4 We previousely ordered replacements from you for this job and recieved the wrong balancers. SEE PICTURE. The balancers on the left are what we need to replace. The ones on the right are what you s ... (cont.)

Hello my name is Gabriel and I am trying to f8nd the water stripping foe my existing exterior commercial door or something similar please let me know I will appreciate it.Thank you so much

I'm looking to see if you sell just the roller parts to the part 23-22c. I just need the little rollers on the top and was wondering if you sell those separate from the whole replacement. Thank you

Channel Balance part number 3625 37 inches

Hello- I'm need to replace my key cylinder on my French inswing door. I only markings I can find on the door handle is CES and in the inside of the face plate is says M374. Can you assist?

Lock is stuck in the locked position. Very old. I would like this one to have a key lock.

Greetings,I want to find out if you have the following snap-in glazing beads available. There are two glazing bead designs used in my window, one for the Horizontal dimension and a different design for the Vertical dimension. I am sending you separate emails for each bead design along with attached ... (cont.)

I need to replace the pile weather-stripping of our Jeld-Wen windows. I apparently did the math wrong, since the 58-021 was too short to match what came out of our windows. Our windows do have a fin-seal in the middle of them. The color of our windows are called "sand". Please advise. Also, will we ... (cont.)

Johnson Pat. 4478006 Are there substitute plastic guides? Are there replacement brackets (up and down)?

Looking for a replacement for this sash corner bar for a double hung window. The manufacturer code from it was #900-21580. Thank you!