Viewing all customer Discussions for:

Other

I want to fix the weatherstripping on the commercial windows. It seems that they are shrinking please help.

I need to get replacement parts for 4 casement windows 4 right top and bottom and 4 left top and bottom. could you please help me in selection the proper parts.

There are no markings but the part is on the bottom of the window pane as shown in pictures. The windows were Marvin windows probably manufactured early 80s. Marvin.com said they discontinued that part and advised me to check with you guys.

Need 2 of these for top and bottom of framed glass shower which has a encased rod.

These all broke at the top where they anchor into window frames. Thanks for your help

The bottom part is cracked, so the piece that turns with the window tilt falls out the bottom. There are no names, numbers, or markings on any of the pieces. Thank you for the help!

Do you have these available?

I need some Ellipse cranks with 13-1/2" arms per this photo. 3 pcs for LH casements in white.

On the coils I see 5.0 35" 5232208. The windows are Alenco. On the pin there is a 2. I need all parts shown in the photos to make complete sets for windows that need repairs made.

The Amerock D2911C1214 Hinge is Finished in Nickel. SPECIFICATIONS "SELF-CLOSING, CONCEALED" 1-1/4In(32Mm) Overlay Hinge Part No. D2911C1214

I ordered and replaced six S795-30, option: 30C, 30 inch series 795 channel balances for three windows. Unfortunately, The pivot bar for one window is broken and needs to be replaced. The current part (broken off) is etched with a number "4", and the first screw hole is one inch from the edge. How ... (cont.)

I have a number Peachtree windows that I need and want to replace the channel balances in. The balance is stamped 2460 B.S.I. as shown. There's no plastic pieces on the ends of the balance, assuming a previous owner didn't remove them on the one window I've taken out.Can you please tell me if you h ... (cont.)

Part number given to us by Pella: 0dg80001. The handle needs to be replaced with a key entry handle. Distance between mounting screws is 6-3/4 inches.

This photo I have attached is a top, or bottom, view of two sliding door interlocking channels. The picture depicts the exact configuration I am looking for. Although, I still need to verify the the gap spacing between the sliding panels. This is mounted vertically on the sliding panels wood framed ... (cont.)

Hi, I'm trying to identify this small nylon piece out of an old shower door - I appreciate that the photos are not the most helpful as it's already broken and there should be another arm on the other side. There are 8 of them in total on a sliding glass shower door, 4 on the top and 4 on the bottom ... (cont.)

1"x3" Millco right and left track latch with mounting screw holes 2 inches apart. Zinc diecast pivot bar (I do not know if the part is handed). Approx 2.5" OAL x ~5/16 wide x ~3/16 thick. Holes are ~11/16" apart and one hole is ~1 5/16 to 1 3/8" from the flared end.

Need to replace sash balances on Andersen window. i think it is late-1980s. The most prominent number on it is 11600 - 17. But other posts tell me that number is irrelevant. Then the number in the photo is, as best I can read it: BE17 9#27 2-87. Pls advise.

I have a upside down T shaped plastic insert in my closet door track. It has concave wheels that ride on it and is rounded. Do you sell the insert mine is cracked and seems to be worn out, bottom of wheel guide drags.

Looking for a replacement lock assembly for this LP door. Overall length of the part is 16". Thank you

The metal cam broke on the pivot shoe for my WindowWorld vinyl double hung tilt-in window.