Viewing all customer Discussions for:

Weatherization

Good Afternoon, I am trying to find some replacement weather stripping for my home windows. Not sure of the window manufacturer. The stripping fits in a groove on the bottom and top of the window. The diameter of the "Bulb" 1/4". The length of the groove portion is 6/32". I need approx 20 ft of s ... (cont.)

Hi, I have 5 Crestline sliding windows. All are marked L29303X42C4M between the panes of glass. I need to replace the weather stripping shown in the attached profile pictures. Can you help me? Thanks Kirk

Please advise which part number the window felt is, please. And are they all the same size on a window. A noticed some staples in a few of them. Do i need to staple them in as well? Thanks

I just bought your long throw weather stripped face place for my entry commercial door. However, the weather strip (wool pile) doesn't stand tall enough, so it leaves a gap to the other door. It's about a 1/4" gap, which really makes a negative impact here in Massachusetts. Do you have a facep ... (cont.)

Attached pictures are for weatherstripping for Traco windows that has gone bad. 3rd photo is the markings with in the glass. Is this product available?

Hi I have 4 doors that need to have the bottom seal replaced but am unable to find the right seal in any of our local building supply or hardware stores. I have taken measurements and pictures of the part. they look like the part #58-189 but is only a bit over 3/4 inch wide (front to back) and only ... (cont.)

This weather stripping has an edge that presses into the wood around the windows allowing it to be held in place securely. The round part of the weather stripping is about 1/4" dia. Nearly all the weather stripping along our house windows is cracked, broken or partly missing. Although I could ... (cont.)

This is a Caradco bottom sweep that I need to replace. The bottom fins have completely disintegrated. The door is 1 3/4 inches thick, 36 inches long. Kerf space is 1 1/4 inch.

Do you carry this bubble seal?

I tried contacting you a few weeks back, but no response. trying this again. Please let me know what you have that might work.

hello I am looking for bulb weatherstripping for M&W windows. This weatherstripping seperates the upper and lower sashes and mounts in the side frame. See pictures. The dimensions are: bulb diameter=12/64", backing width=12/64" and overall bulb height=17/64. Thanks

Can you give me a quote on this if you can match it.

Hi, I would like to get the correct part to replace weather stripping on my casement windows. I think the manufacturer is HUNT. Attached is a pic. The L section is 1/4 of an inch on either side, with one small groove/spike to hold it to the window. The bubble is also around a 1/4 inc ... (cont.)

All the weather stripping has become brittle on sashes and screens. I measure 3/16 by 3/16. Is the same size used on sashes and screens or can it differ?

doesnt look like you carry this sweep. I have been unable to find it anywhere. bulb and fin style that slides into two grooves on underside of door. any suggestions for where i might find this? thanks for your help.

Hello, yesterday I ordered some lengths of 58-045 to replace the worn out 40 yr. old wool pile insulation in several 43 year old sliding glass doors. Having pulled out a strip, I measured and decided that the 9/32 x 1/4 was the best fit, even though the new strips have a plastic fin in the center ... (cont.)

The storm windows are possibly from the 1960's? The profile of the weatherstripping is very narrow (1/8 " - 3/16") and the depth is hard to determine because it is so worn - maybe an 1/8". I have included images showing an overall half section of a storm window, details of the weatherstripping b ... (cont.)

Hello, Looking for replacement bubble seal for these dimensions. Do you have them in these sizes ? Thanks Patrick

We are having a hard time locating weather stripping that is pictured. It is for EXTERIOR DOOR BOTTOM WEATHER STRIPPING. We need 40" long.

Could you please recommend a door sweep for this 36" wide metal entry door? I believe this is the original door from the mid 70's, so it doesn't have to be exactly the same, just looking for an effective solution. Thank you!