Viewing all customer Discussions for:

Weatherization

Hello, I am in need of some weather stripping for windows that were installed in our home in 1991. They are the MW freedom clad vinyl. The weather stripping is a rigid strip that slides into a channel. It has a flange and then a "V" hook that goes in the channel.. The windows roll out to one side. I ... (cont.)

I need the piece of weather stripping that goes on the face plate for a kawneer commercial door long throw the little flat slide on piece is approx. 5/32 wide with a wool pile about1/4 - 5/16 high do you have such an animal or can I trim the one you have to fit? ( yours is 9/32 )I did buy a couple o ... (cont.)

I am looking for weatherstripping for the bottom seal from an old Alenco window. The window has noted on it the following: Code 50-1, "HP" Series. I need 30 feet of this weatherstrip seal. Please see the attached file for a picture of the old seal, along with the dimensions. Thank you. ... (cont.)

Weather stripping

I'm replacing the bubble seal on my vinyl casement windows. I can remove most of it w/o problem except for few areas where the bubble part has seperated from the flange part that secures it in the track. I'm having a devil of a time trying to remove it so I can insert the new stuff. Any suggestions? ... (cont.)

What is the best way to remove the old pile weatherstripping? Screwdriver? And them to reinsert new pile? Screwdriver again?

Windows are 25 years old and have the original weatherstripping. 1/2" overall length, 14/" bulb & 1/4" stem. What do you have that will fit . Thanks Peter

I am looking to replace the door sweep on my Stanley Door. Please help identify a correct replacement. Thank you

For door 595830 Is this deep enough?

Hi Dave, I just purchased 58-008 and I've had to replace the door jamb for which the kerf gets inserted into. How wide should I make the kerf in the new jamb? Thanks! Kind Regards, Mike from Wantage, NJ

To whom it may concern. My house was built in 1988. The Coradco windows are still performing efficiently, except for the gasket material in between the sashes and at the top and bottom edges. This material has a .300" diameter bead with a double arrow headed barb, with an overall height of approx. . ... (cont.)

I have received six (two orders of three each) 48 in Duodurometer Door Bottom Sweeps 58-186. Doors were thought to be 1 3/4 in. but are actually 1 7/8 in. Otherwise 58-186 would have been perfect. Three doors are 36 5/8 in wide and three are 37 1/2 in. Since threshold has sunk on the end of one ... (cont.)

I have attached some photos but is difficult to see. I want to avoid cutting a piece until I know Incan replace it. There are over a hundred of these in my building that all need replacing. I think it is most similiar to 58-181 Pella push in weatherseal. Can you advise?

5/8 backing. This slides into a channel between the two sashes at the interlock as an air dam. It's a very stiff backing, most likely sold in strips as opposed to rolls. See attached photos. Client is looking for 300

Hi, I'm looking for replacement of weather strip for commercial double door. Base measures is 1/2" and the pile height about 8/16". Thank you very much for your help.

The weatherstripping is a 1/8" high felt on a 3/8" backing. It slides into place on the edge of the storefront commercial door. What do you recommend as a replacement? The gap between the double door is about 1/8" If there was a longer felt installed, would it keep the door from closing properly? ... (cont.)

The weather striping is starting to fall apart and I need to replace

slide in side base 1/4" with 3/4 in door 35 years old. t.y. have a great day !

do you have this type of weather stripping< its rubber

Please quote price and delivery for 250 feet or minimum order quantity. Material is the same as your p/n: 58-053. Sample is available upon Request.