Viewing all customer Discussions for:

Weatherization

Hello, I'm looking to replace my weatherstripping. I have both a bubble and pile. Pile is 3/16" x 1/4" 58-127 (?) Bubble is 3/16" x .187" I'm not sure if I need 58-182 or 58-183. I've attached photos, if you can take a look at it and let me know what product I need. Thanks, Ari

I think these windows were the BLue Chip Belmont, installed in the 1980s. The stripping helps keep the rain outside.

Want to replace old brittle rubber gasket / weatherstripping on crank out Truth (30744) windows. Here's a few pics of what I have that I want to replace.

This is from an exterior door weatherstripping that was installed in 1999. I believe it is a Marvin brand door. Can you help me find this weatherstripping and the manufacturer that makes it? I need to replace it. Marvin is of NO help! Thanks

Single hung vinyl windows about 15 years old. The weather strip is 32 1/2 inches long and simply slides into a grove on the bottom part of the window sash. Please advise if you sell a replacement. Thanks.

can you help me find it

I have custom (painted) steel doors and frames on my modern house. I have wool weather stripping that I think is your 58-099 or 58-105. It was apparently glued on, and does not sit in a track. Should I remove the old stuff with a putty knife? What sort of adhesive do you recommend to attach new ... (cont.)

I am going to install a swinging door between the kitchen and "office" and would like to have the door 'seal' somewhat when it closes. (center of jamb) Can I dado a slot and install a seal the door would stop at but go in our our? -or- What about a seal in the edge of the door for easier (more ... (cont.)

Here are a couple pictures of the door sweep I need to replace or at least replace the vinyl piece if I can. The aluminum piece is 38.5" wide and has 7 screws and the door brand is Kawneer.

I have three (4'x4') aluminum basement windows that need the weather stripping replaced. I think the sides (I included 2 pics- IMG 0876/0878) and the top use the 9/16 commercial bubble weatherstrip. Please let me know what you think. The bottom uses a different type of weather strip and I can ... (cont.)

Hello, I am in need of some weather stripping for windows that were installed in our home in 1991. They are the MW freedom clad vinyl. The weather stripping is a rigid strip that slides into a channel. It has a flange and then a "V" hook that goes in the channel.. The windows roll out to one side. I ... (cont.)

I need the piece of weather stripping that goes on the face plate for a kawneer commercial door long throw the little flat slide on piece is approx. 5/32 wide with a wool pile about1/4 - 5/16 high do you have such an animal or can I trim the one you have to fit? ( yours is 9/32 )I did buy a couple o ... (cont.)

I am looking for weatherstripping for the bottom seal from an old Alenco window. The window has noted on it the following: Code 50-1, "HP" Series. I need 30 feet of this weatherstrip seal. Please see the attached file for a picture of the old seal, along with the dimensions. Thank you. ... (cont.)

Weather stripping

I'm replacing the bubble seal on my vinyl casement windows. I can remove most of it w/o problem except for few areas where the bubble part has seperated from the flange part that secures it in the track. I'm having a devil of a time trying to remove it so I can insert the new stuff. Any suggestions? ... (cont.)

What is the best way to remove the old pile weatherstripping? Screwdriver? And them to reinsert new pile? Screwdriver again?

Windows are 25 years old and have the original weatherstripping. 1/2" overall length, 14/" bulb & 1/4" stem. What do you have that will fit . Thanks Peter

I am looking to replace the door sweep on my Stanley Door. Please help identify a correct replacement. Thank you

For door 595830 Is this deep enough?

Hi Dave, I just purchased 58-008 and I've had to replace the door jamb for which the kerf gets inserted into. How wide should I make the kerf in the new jamb? Thanks! Kind Regards, Mike from Wantage, NJ