Viewing all customer Discussions for:

Weatherization

I need to replace the weatherstrip of my front door. Here is a picture of it. The base is 1-1/8" wide. My door is 8' x 3'.

I have a client with casement windows who needs many of them re-weatherstripped. This is a photo of the product, do you have something like this?

Are there any videos showing how to replace a t-slot bulb seal?

need to find rubber strip or weather strip for the bottom of the bottom window

Hi, I attached pictures of two different piles in my window. IMG_1376 and 1380 are of the first sample and IMG_1382 and 1382 are of the other. I believe the first is 5/32X1/4 and the other believe is 9/32X1/4. The last picture is of the profile of each. The first one on the left and second on r ... (cont.)

looking for a replacement for this seal

This is the bubble weatherstripping at the bottom of my windows. The channel if fits in is 1/8 inch. The measuring the bubble diameter at 9/16.

I am looking for this prime door sweep with tabs. I can't use something like 58-186 as a replacement because I have kick plates on the door. Do you have any suggestions?

My customer requires a replacement entry door bottom seal. I attempted to use 58-189 but it would not work. The center tabs on the bad seal two attaching tabs are spread apart slightly more than on 58-189 and they are a little higher and they had an angled edge on the outside top that hooked on the ... (cont.)

Is a special tool required to install #58-135 or #58-134 insulation at the bottom of a window? Does the sash need to be removed before replacing the insulation strip?

This is weatherstripping from the frame of a commercial entry door. If it doesn't look familiar I can mail you a section. Thanks. Bob

I made a drawing, but I did not have a program to convert it to any forms that you would accept, so I took a photo of the screen. The second photo is the profile I was drawing. the third shot is the outside side of the strip. Will the bubbles keep the window from going down far enough to lock? ... (cont.)

This is for survivor 5500 windows.

I need to replace some interior door weatherstripping.It is very similar to 58-053.The old weatherstripping doesn't have the horizontal fins like the 58-053 but just one small vertical fin.In other words there is just a fin below the bubble but nothing on the side of the fin.The old weatherstripping ... (cont.)

Hi I am replacing the stripping for vinyl windows made by Gorell. It appears I need item 58-182. The T is 3/16 and the bulb appears to be 1/4 or 5/16. Thanks for confirming. Kate

Hello- Similar to what someone previously posted several years ago, I am seeking weather-stripping for old casement windows installed around 1988. I have attached several photos. Dimensions are: Push-in double barb is about 1/4" long. The length of the main base is 1/2" wide. The height of ... (cont.)

My patio door faces south and the backing on its pile weatherstrip disintegrated in the sun causing it to fall out of the vertical groove. The width of the backing is 0.3" and its two-ply pile stands 0.25" high. (see 3 pictures attached). Hail has also broken the the lower vinyl glazing beads on ... (cont.)

I need to replace the weatherstripping on my crank out casement kitchen window. I believe it is a Patriot window and was installed when the house was built in 1994. I've attached photos and the measurements I took are as follows: The base is 1/4" the "bubble" (although deformed) seems to be ... (cont.)

I am trying to find this window seal hope this pictures help because I have no clue what brand windows this are when I measured the T channel it looked to be about 3/16 to 1/4 can you help me out . Thanks bunch

Hello Swisco, looking to replace the bottom rubber sealer underneath my front entry door hard to find do you have anything similar to this? The old piece had 2 holes cut into it to be able to secure in place. The old piece base was approx 3/4" and fit into a hollow u shaped channel in the bottom o ... (cont.)