Viewing all customer Discussions for:

10-109 7/8" Flat Shower Door Wheel

I have 1970 era sliding mirrored closet doors. The rollers hang from the top of the door. The rollers spit out the bearings and I can't find replacement parts. An aluminum rectangle piece about 2.5 inchesX 3/4 " wide slips in a channel vertically. It has the wheel on top at a right angle to the al ... (cont.)

I am looking to purchase some nylon rivet axle rollers. Specifications: .900" Dia x .250" wide (nylon piece) axle dia. - .462" x .155" shoulder length rivet dia. - .250" x .093" shoulder length Thank you, Randy

Hi I am hoping you can help me find replacement parts for 6 glass Slider doors from around 1976 Each door is about 30x94 . I am hoping to replace wheels and feet if possible. Thank You in advance for your help Sincerely Mary-Ellen Ps... I think this is a wonderful idea and I will spread th ... (cont.)

Hello, I'm in search of the entire hardware assembly as shown in the pictures. The length of the aluminum T-bar is roughly 2-3/4 inches. width is about 5/8", with the inner rail being 3/8" wide. Hope my description will someone translate correctly with the use of the picture. Appreciate any help tha ... (cont.)

Hi, I'm looking for rollers to replace some ball bearing rollers for my kitchen cabinet drawers. I've included pictures and dimensions that I was able to determine. I have no idea the brand name of the rollers. Please let me know if you need more information. Thanks Gary

Frame width 1". Can you help ? thanks by advance, & happy new year

I am looking for drawer slide roller bearings The diameter is 7/8" 1/4" wide with a 1/4 20 bolt about 3/8" long Do you have anything that comes close to that ?

I purchased your shower door roller 10-152 based on your customer discussions surrounding the Allen Stevens shower door roller A-S 3937. The replacement wheel is considerably smaller than the original which in 1" in diameter. before I bring a handyman out to install this , I'd like to know if you t ... (cont.)

The hardware on our kitchen drawers is Grant 338. They were installed in 1985. The front roller on the drawer guide has broken. Are the parts still available, or is there a replacement that you could recommend?

right drawer rail Grant CR 348 22" long /roller disk is broken but is 7/8" ,the rail is 1 inch wide with interior 3/4 to 7/8 were roller fits in to.roller

I need to replace drawer roller or ring for a steel drawer. The drawer faceplate is 30" wide and 6" high. The roller is a hair over 1" (28mm) outer diameter and exactly 1/4 inch deep. Photo a: Damaged nylon roller Photo b: Roller wheel without ring Photo c: Remaining roller

This is a built in file cabinet in our house and the wheels for the slider have disintegrated. They look to be 7/8" wheels made of nylon. Looking for a replacement wheel or the whole slide unit itself. The slide is 13 1/2 on file cabinet. Any help would be appreciated. Thanks! Dylan ... (cont.)

Hello I am looking for replacement Rollers for the Drawers in my Steel Office Desk. They are actually a Plastic or Nylon Roller bearing that is riveted into the drawer into a hole on the rear sides of the drawer on both the left and right side. They fall out after time from the holes they are rivete ... (cont.)

US Patent # 3980364 15000AB-3 (not sure what this number is) The wheel broke in half on the right side plate. Please help!! Thank Katherine

Older mirror door for a closet. Need a top not an off set roller mount.

I had this desk powder coated and I did not remove the roller wheels for the drawers. They were 1 in D and 1/4 in thick with about a 3/8 bore I think. Do you have anything that work as a replacement? Thanks Ben

Hi there. I've been looking all over to find a replacement roller for the drawer in my roll top desk. I don't need an axle as the post is still there and there's no hardware to remove that I can find. The other roller measures an inch. Can you guys help? Appreciate any direction you can ... (cont.)

Good morning, Your company was referred to me by Rockler Woodworking and Hardware as someone who might be able to help me. I have a pair of Sauder Select Collection Mobile Metal File Cabinets. The bottom file drawer is supported on and slides out on white plastic 7/8

I've spent more than a year trying to replace these wheels for my steel file cabinet. I went with someone's 7/8" roller, but that didn't work. Do you have anything I can try?

The wheel on the cabinet no longer works. Took apart and bearings fell out. It is 20yrs old. What is it? What make? Lowes and Home Depot do not have it. Please get back to us. Length 22 inches Wheel was 7/8? Estimate. Thank you.