Viewing all customer Discussions for:

58-021 Gray Pile Weatherseal, 3/16" x 3/16"

I sent two new pictures It looks like 3/16. X 3/16

Please see pictures. Measurements seem to be 1/4 x 1/4? But I didn't find this size on your site? Please let me know your review? I don't know the manufacturer but I believe they are Pella windows. Since my sliding doors are Pella? I have approximately 3 double hung windows that need replacing ... (cont.)

We have 3 windows of the same size. They each have 2 balance springs, 1 bottom rubber tube weather stripping and 2 wool pile weather stripping on the sides. The main spring channel is 28" long. The bottom tube weather stripping is 3/8" diameter with a channel t bottom of 34" long. The side wool pi ... (cont.)

My window pile appears to be 3/16 x 3/16, what is the correct replacement part number for this item and am I measuring correctly?

I believe I need the S795-26c but if you can confirm with the pictures please? I believe these are Renewal by Anderson windows. The pin holding the spring failed or the guts failed due to rust.

Hi, Enclosed pictures show the two sizes I need for my Crossley windows. The biggest is 5mm pile and 5mm width. The smaller one is 3mm pile and 4mm width. I don't know if you have these sizes. I'd only ned a small sample like an inch or two to see if it will fit in the slots of my windows. I will l ... (cont.)

Hi, I would like to replace pile weatherstripping in Champion windows that are 25 years old. Windows are in good shape but weatherstripping is shot. As you'll note in the photo sent, there is no way to insert the plastic strip into the slot because they are blocked by side frames that are not remov ... (cont.)

Hello, I am having trouble accurately measuring my bubble seal and pile parts. First the bubble seal t slot is very close to your .187 width, BUT the hollow bubble appears to be about .4 inches, not .3 that you sell. Second, the pile weatherseal has a base of about 3/16 inches like your number58-02 ... (cont.)

Do you carry this seal strip? Plastic backing of this fuzzy strip is 3/16" wide that fits into a Tee slot channel along perimeter of exterior side of the sash. May come in extended lengths or roll that is cut to fit.

Pile appears to be 3/8" but is worn. Base width is 3/16".

Hello, can you please help me I need to get weatherstrip pile with clean fin My window is .187 inches base and height is I am thinking ether .187 or .200 Please help

Hello I'm looking for the right weather stripping for an older millguard patio sliding glass door. It's the type of weather stripping that has brush and a piece of rubber for seal. It goes in the tracks. Thank you very much

Hello there, I'm trying to identify which Pile Weatherstripping I need for my sliding door, I attached a picture with the numbers the door has in the glass also the Pile Weatherstripping measurements. I'll be more the happy if you can help me with this issue. Antonio

Help identify weather stripping.Base 3/16" Pile 1/8" There is a thin rubber strip as well.

IWe need to replace the'hair' weather seal on our church's front door.

I need to replace the pile weather-stripping of our Jeld-Wen windows. I apparently did the math wrong, since the 58-021 was too short to match what came out of our windows. Our windows do have a fin-seal in the middle of them. The color of our windows are called "sand". Please advise. Also, will we ... (cont.)

Hi, I have Milgard windows with old weather stripping that needs replacing, I took out a section and it measures 3/16 x 3/16 with a plastic strip, I found 58-021 on you Website. Do you think the height may be more because its old ? Thanks in advance

Just wondering if you could help me identify this seal .it is not glued in just slides in a grove on the sliding door if you could help that would be fantastic thanks andy

It looks like you offer the window seal in grey but I do not see it in white.

All the windows in my home are from the same manufacturer. The one that looks like a brush fits into a 3/16 slot. The other one also fits into a 3/16 slot, but it has a short nap brush with a plastic strip down the center.