Viewing all customer Discussions for:

58-127 Pile Weatherstripping, 3/16" x 1/4"

I am looking for replacement stripping for double entry doors. The metal strips that hold the stripping is approximately 1/4" x 9/16". Each door is 83 1/4" x 38". There is also a strip along each mortised latch set that needs to be replaced. Both the metal strips and the insulation stripping its ... (cont.)

I am interested in finding out about product #58-127...We have double doors at my job and the felt weatherstripping is missing leaving a gap between them leaving all the cold air to come in..We cut a piece off,and the measurements are 3/16 x 1/4..I want a good seal,and was wondering if this is the s ... (cont.)

the bottom white is 3/16" x 1/4" black pile I will need about 500' there is no numbers

These are circa 1997 Mastic Inner-lok Vinyla Replacement windows. None of the parts you show match up exactly, but do you have parts that will work? I see some sash release levers that are close. Not sure about the pivot shoe, or if I have even identified that properly. Thanks so much ... (cont.)

I have 1997 ceritenteed windows I have installed part # 58-127 3/16 x1/4 weatherstripping,no problem however on the bottom of the top window the seal appears to be 3/16 x 5/16 wool pile which I cannot find on your web sight any suggestions?thanks Rick

My stripping does have a fin seal and has a 3/16 base. It appears to measure 7/32 tall but you offer 3/16 or 1/4 tall. What is the proper replacement? Thanks.

Need help identifying

Hi! I'm hoping you can help me find the correct replacement weatherstripping for my tilt-in windows. I've included some pics to help. The space I measured for the stripping to slide in is about 4/32 with a little bit of space on either side, so I'm guesstimating maybe 5 to 6/32 tops. The pile that's ... (cont.)

the bottom weather-stripping attached to the bottom track needs to be replaced.it has a bulb stripped attached to the track the door slides on. the Kolbe door is 17 years sold

We have 10 "Certainteed" windows of varying sizes which need to have the weatherstripping replaced. The windows were installed in 1996 and both the white fuzzy fibers and skinny plastic core which them have deteriorated badly over time. The fuzzy stripping is located on the lower window which can b ... (cont.)

Slides into a slot on in the window.

I plan to refresh 20 windows and experimenting with first. I have determined I require the flowing for each window. 1) 5 sections of pile weatherstripping 3/16 x 1/4 2) .187 T-slot foam filled bulb I need advice for removal of pile weatherstrip section where it interlocks top sash. It seems to ... (cont.)

Looks like a half an inch channel

Hi, I am looking for parts for my windows. I wonder can you help ? Thank you for posting Youtube videos. Regards, Chun-Lung Lim

Nightmare scenario - I tried 58-127 first but it would not thread into the slot. Then I tried 58-042 and it fell out of the slot!!! How can that be when the former is narrower than the latter? See pictures of the seal slot with uniform swages the length of the track. Are those normal? I had a ha ... (cont.)

My window has wool pile and bubble seal. The wool pile currently measures 3/16 x 5/32, but it has been flattened a bit. Should I move up to 3/16 x 3/16? The bubble seal has a diameter of 5/16. It runs along the bottom edge of each window in the double hung unit. Not sure what kind to choose. ... (cont.)

can i use a higher wool pile than the one removed from the window frame

looking for this felt .

Balance is 26 in weather strip is 31.5.

I have 1980's vintage Acorn windows and am looking for replacement weather stripping for them. Can you help with that material? Thanks, Mike